Honeywell D1-528 Direct Thermostat Installation Guide
INNCOM DIRECT D1-528 THERMOSTAT INSTALLATION GUIDE
c. Press the F/C button.
Str (store) will be displayed.
mode will automatically be disabled. If the room gets
unrented during this time, LEM mode will be dis-
abled.
d. Press DISPLAY to store the change.
The D1-528 will reset.
To enable LEM mode (without entering service
mode):
When the D1-528 starts up, it will display a P
indicating it is in Contractor mode.
LEM can also quickly be enabled without entering
service mode by performing the following on the
D1-528:
To Disable Contractor Mode:
a. Press the UP/DOWN arrow button if on is
displayed, to change to oFF.
b. Press DISPLAY button.
1. Press and hold the DISPLAY button.
2. Press and release the POWER button
3. Press and release the UP arrow button
The D1-528 will beep, Ctr will appear on the
display and OUTSIDE will start blinking on the
display indicating that the change needs to be
stored.
4. Release the DISPLAY button.
LEn will quickly appear in the display indicating LEM
mode is active.
c. Press the F/C button.
Str (store) will be displayed.
To disable LEM mode:
d. Press DISPLAY to store the change.
The D1-528 will reset. Contractor Mode is now
disabled.
1. Select oFF and press DISPLAY.
The D1-528 will disable LEM mode and beep. nor
(normal) will appear. LEM mode is now disabled.
To disable LEM mode (without entering service
mode):
Limited Energy Management Mode
LEn
LEM can also quickly be disabled without entering
service mode by performing the following button press
sequence on the D1-528:
LEM can be enabled in the D1-528 when an important
or discriminating guest is checked into a room. A room
placed in LEM mode uses expanded target temperature
control bands (allows guests to select higher/lower than
normal room target temperatures) and does not use
larger temperature control bands when the room
becomes unoccupied, or the room window or balcony
door is open.
1. Press and hold the DISPLAY button.
2. Press and release the POWER button.
3. Press and release the DOWN arrow button
4. Release the DISPLAY button.
nor (normal) will quickly appear in the display
indicating LEM mode is disabled.
1. Press and hold
mode.
2. Press the UP/DOWN arrow button and select LEn
for 4 seconds to enter into service
PIR Motion Sensor Test (Plr)
Use Plr to test the built in motion sensor in the D1-528.
parameter.
1. Press and hold
mode.
2. Press the UP/DOWN arrow button and select Plr
for 4 seconds to enter into service
ºF ºC
parameter.
ºF ºC
A
DISPLAY
3. Press the DISPLAY button.
on will appear on the display by default.
4. Press the UP/DOWN arrow button to select between
on or oFF.
To enable LEM mode:
A
DISPLAY
3. Press the DISPLAY button to start the test.
V 0 will appear on the display.
1. Select on and press DISPLAY button.
The D1-528 will enable LEM mode and beep. LEn will
appear on the display. LEM mode is enabled and will
remain enabled for 72 hours. After 72 hours LEM
25
31-00721-01
| General | Details |
|---|---|
| Name | Honeywell D1-528 Direct Thermostat Installation Guide |
| Make | Honeywell |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.63 MB |

Honeywell T6 Pro Programmable Thermostat User Manual

Honeywell FocusPRO P200 Programmable Thermostat User Guide

Honeywell RCHT8610WF Series Smart Thermostat Installation Guide

Honeywell T9 Smart Thermostat Installation Guide

Honeywell TH2320WF4011 FocusPRO Smart S200 Series Thermostat User Guide

Honeywell TL116A Thermostat Installation Guide

T10 Pro Smart Thermostat with Redlink Room Sensor

Honeywell TH6320WF2003 Lyric T6 Pro Wi-Fi Programmable Thermostat User Guide

Honeywell Lyric T5 Wi-Fi Thermostat Installation Guide

Honeywell RTH9580 Wi-Fi Color Touchscreen Programmable Thermostat User Guide




















































