Honeywell D1-528 Direct Thermostat Installation Guide
INNCOM DIRECT D1-528 THERMOSTAT INSTALLATION GUIDE
1. Press and hold
mode.
2. Press the UP/DOWN arrow button and select Uot
for 4 seconds to enter into service
UrS (Unrented Setback)
The Unrented Setback (UrS) parameter allows the
selection of Normal, Aggressive or Minimal savings
based on different temperature control bands that
become active when the room is unoccupied and
unrented.
parameter.
1. Press and hold
mode.
2. Press the UP/DOWN arrow button and select UrS
for 4 seconds to enter into service
ºF ºC
parameter.
A
DISPLAY
ºF ºC
3. Press the DISPLAY button.
V and the current selected Uot value will be
displayed. 1 - Normal is the default value.
4. Press the UP/DOWN arrow button to select the
desired Uot value 1,2 or 3 as per the below table.
A
DISPLAY
Table 21 Uot (Unoccupied Time) range
3. Press the DISPLAY button.
Parame
ter
V and the current selected UrS value will be
displayed. 1 - Normal is the default value.
4. Press the UP/DOWN arrow button to select the
1
2
3
Uot
Nor
mal
Aggr
essiv Mini
mal
desired UrS value 1,2 or 3 as per the below table
(Unocc
upied
Time)
e
Table 22 UrS (Unrented Setback range)
Door
Rented
10
min
5
min
30
min
Parameter
1
2
3
Switch
and
Motion
UrS
(Unoccupi
ed Delta)
Norma Aggres Minim
Unrent
ed
2
min
2
min
10
min
l
sive
60 °F
85 °F
al
Lower
Upper
62 °F
80 °F
65 °F
75 °F
Motion
Sensor
only
Hours
Bright
2.5
hrs
1.5
hrs
8.5
hrs
Hours
Dark
24.5
hrs
12.5
hrs
33.5
hrs
5. Press the DISPLAY button to save the value.
UrS will display and the D1-528 will beep and
OUTSIDE will start to blink on the display indicating
that the value needs to be stored.
5. Press the DISPLAY button to save the value.
Uot will display and the D1-528 will beep and
OUTSIDE will start to blink on the display (if is not
already blinking) indicating that the value needs to
be stored.
6. Press the F/C button and Str will appear.
7. Press the DISPLAY button to save the change.
The D1-528 will reset.
6. Press the F/C button.
Str will appear.
Urt (Unrented Time after Unoccupied)
7. Press the DISPLAY button to save the change.
The D1-528 will reset.
This setting only applies if no PMS is installed at the
hotel to rent and unrent rooms. With no PMS, all rooms
would normally always be Rented and thus no unrented
temperature setback (i.e., a wider temperature control
band when unrented) could be used to save energy.
Urt allows the selection of Normal, Aggressive or
Minimal savings based on making the room go
unrented after the room has been unoccupied for a
certain time period.
31-00721-01
22
| General | Details |
|---|---|
| Name | Honeywell D1-528 Direct Thermostat Installation Guide |
| Make | Honeywell |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.63 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Honeywell T6 Pro Programmable Thermostat User Manual
Honeywell FocusPRO P200 Programmable Thermostat User Guide
Honeywell RCHT8610WF Series Smart Thermostat Installation Guide
Honeywell T9 Smart Thermostat Installation Guide
Honeywell TH2320WF4011 FocusPRO Smart S200 Series Thermostat User Guide
Honeywell TL116A Thermostat Installation Guide
T10 Pro Smart Thermostat with Redlink Room Sensor
Honeywell TH6320WF2003 Lyric T6 Pro Wi-Fi Programmable Thermostat User Guide
Honeywell RTH9580 Wi-Fi Color Touchscreen Programmable Thermostat User Guide
Honeywell Smart Color Touchscreen Programmable Thermostat RTH9590 User Manual
White Rodgers 1F72 5 2 Day Programmable Thermostat Instructions
Decdeal HY607 WIFI Digital Heating Thermostat User Manual
Braemar BRA639659 Manual Digital Thermostat Instruction Manual
BEOK TGP53 Wifi Thermostat User Guide
EMERSON ST765470 Digital Thermostat User Manual
BEOK TDS21WIFI-AC Fan Coil Thermostat Instruction Manual
SALUS CONTROLS SQ610 Quantum Smart Thermostat User Guide
ZigBee BAC-3000 Series Thermostat User Guide
MAGNUM FIRST M9-TS1 24 Volt Intelligent Thermostat Owner’s Manual
Honeywell Home S200 Series FocusPRO Smart Thermostat User Guide