Honeywell D1-528 Direct Thermostat Installation Guide
INNCOM DIRECT D1-528 THERMOSTAT INSTALLATION GUIDE
1. Press and hold
mode.
2. Press the UP/DOWN arrow button and select Urt
for 4 seconds to enter into service
2. Press the UP/DOWN arrow button and select PAn
parameter.
parameter.
ºF ºC
ºF ºC
A
DISPLAY
A
3. Press the DISPLAY button.
DISPLAY
V and the current selected PAN ID value will be
displayed. PAN ID 1 is the default value.
4. Press the UP/DOWN arrow button to select the
desired PAN ID.
5. Press the DISPLAY button to store the new PAN ID
value.
3. Press the DISPLAY button.
V and the current selected Urt value will be displayed.
1 - Normal is the default value.
4. Press the UP/DOWN arrow button to select the
desired Urt value 1,2 or 3 as per the below table
The D1-528 will beep and will display PAn. OUTSIDE
will NOT begin to blink on the display indicating the
change needs to be stored like other parameters
require.
Table 23 Urt (Unrented Time after Unoccupied range)
Parameter
1
2
3
6. Press the F/C button to exit service mode.
Normal
Aggressive
4 hrs
Minimal
16.7 hrs
RF Channel (rF)
Urt
(Unrented
Timeout)
8 hrs
The RF Channel in combination with the PAN ID is used
to control what a D-578 Edge Router a particular room
communicates through. The RF channel can be set to
any value 11 to 26. The default RF channel value is 20.
Each RF channel uses a distinct frequency band.
5. Press the DISPLAY button to save the value.
Urt will display and the D1-528 will beep and
OUTSIDE will start to blink on the display indicating
that the value needs to be stored.
At any INNCOM Direct installation, one D-578 Edge
Router will be installed using RF channel 20 by default,
and all D1-528 devices will also be set to RF Channel 20
by default.
6. Press the F/C button.
Str will appear.
7. Press the DISPLAY button to save the change.
The D1-528 will reset.
The RF Channel should typically not require changing.
One reason that would require using a different RF
channel is if it is determined there are other RF
transmitters installed at the hotel that use the same or
close to the INNCOM default RF Channel 20 frequency
band. It may be required to use a different RF Channel
for the installed D1-528 devices.
Pan ID (PAn)
The PAN ID in combination with the RF Channel is used
to control what D-578 Edge Router a particular room
communicates through. The PAN ID can be set to any
value 0 to 255. The default PAN ID value is 1.
At any INNCOM Direct installation, one D-578 Edge
Router will be installed using PAN ID 1 by default, and
all D1-528 devices will also be set to PAN ID 1 by
default.
1. Press and hold
mode.
2. Press the UP/DOWN arrow button and select rF
for 4 seconds to enter into service
parameter.
NOTE:
The PAN ID should typically not require changing.
1. Press and hold
mode.
for 4 seconds to enter into service
23
31-00721-01
| General | Details |
|---|---|
| Name | Honeywell D1-528 Direct Thermostat Installation Guide |
| Make | Honeywell |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.63 MB |

Honeywell T6 Pro Programmable Thermostat User Manual

Honeywell FocusPRO P200 Programmable Thermostat User Guide

Honeywell RCHT8610WF Series Smart Thermostat Installation Guide

Honeywell T9 Smart Thermostat Installation Guide

Honeywell TH2320WF4011 FocusPRO Smart S200 Series Thermostat User Guide

Honeywell TL116A Thermostat Installation Guide

T10 Pro Smart Thermostat with Redlink Room Sensor

Honeywell TH6320WF2003 Lyric T6 Pro Wi-Fi Programmable Thermostat User Guide

Honeywell RTH9580 Wi-Fi Color Touchscreen Programmable Thermostat User Guide

Honeywell Smart Color Touchscreen Programmable Thermostat RTH9590 User Manual




















































