White Rodgers 1E65-144 Non Programmable Electronic Digital Thermostat Instruction Manual

1

2

3

4

1E65-144  

Non-programmable Electronic Digital Thermostat  

For Line Voltage Applications  

INSTALLATION AND OPERATION INSTRUCTIONS  

Operator: Save these instructions for future use!  

DESCRIPTION  

The 1E65-144 thermostat has been designed to control electric heating  

systems such as baseboard heaters, radiant floors, radiant ceilings  

and convectors.  

Temperature  

Adjustment  

Buttons  

The adapter plate is used to offset the thermostat when an obstruction  

prevents the thermostat from being mounted directly to the junction  

box.  

Temperature  

Display  

Light  

Button  

The thermostat cannot be used with the following:  

-

-

-

-

a resistive load under 2 A  

a resistive load over 16.7 A  

systems driven by a contactor or a relay (inductive load)  

central heating systems  

System  

Switch  

Parts Supplied:  

One (1) thermostat  

Available Accessories:  

F61-2642 Adapter Plate  

Two (2) 6-32 pan head screws  

SPECIFICATIONS  

Supply:  

120/240 VAC, 50/60 Hz  

Setpoint range:  

Display range:  

Display resolution: 0.1°C (1°F)  

7°C to 32°C (45°F to 90°F)  

0°C to 37°C (32°F to 99°F)  

Minimum load: 2 A (resistive only)  

500 W @ 240 VAC  

250 W @ 120 VAC  

Maximum load: 16.7 A (resistive only)  

4000 W @ 240 VAC  

Shipping:  

Approval:  

–20°C to 50°C (-4°F to 120°F)  

2000 W @ 120 VAC  

PRECAUTIONS  

WARNING  

!

* Failure to read and follow all instructions carefully before  

installingoroperatingthiscontrolcouldcausepersonalinjury  

and/or property damage.  

* Topreventelectricalshock,personalinjury,and/orequipment  

damage, disconnect electric power to system at main fuse or  

circuit breaker box prior to installation or service.  

* All wiring must conform to local and national electrical  

codes and ordinances.  

INSTALLATION  

Installation should be done by a qualified heating and air conditioning  

contractor or licensed electrician.  

Optional: Use the adapter plate accessory if you need to offset the  

mounting holes on the junction box. Align and affix the wall plate to  

the electrical junction box using two 6-32 flat head screws included  

with the plate.  

Loosen the screw holding the thermostat cover to the base, open cover  

on hinge and remove the cover.  

Screw  

White-Rodgers is a division  

of Emerson Electric Co.  

PART NO. 37-6862D  

Replaces 37-6862C  

0839  

www.white-rodgers.com  

https://manual-hub.com/  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	White Rodgers 1E65-144 Non Programmable Electronic Digital Thermostat Instruction Manual
Make	WHITE RODGERS
Language	English
Filetype	PDF (Download)
File size	1.04 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• WHITE RODGERS

White Rodgers 1E65-144 Non Programmable Electronic Digital Thermostat Instruction Manual Overview

Summary of Contents

• Page 1: Non-programmable electronic digital thermostat for line voltage applications. The thermostat is designed to control electric heating systems such as baseboard heaters and radiant floors. The thermostat cannot be used with resistive loads under 2 A or over 16.7 A. Installation should be done by a qualified heating and air conditioning contractor or licensed electrician. To prevent electrical shock and personal injury, disconnect electric power prior to installation or service. All wiring must conform to local and national electrical codes and ordinances. Use the adapter plate accessory if you need to offset the mounting holes on the junction box. The thermostat has a setpoint range of 7°C to 32°C (45°F to 90°F). The display resolution is 0.1°C (1°F). Minimum load is 2 A (resistive only) and maximum load is 16.7 A (resistive only).
• Page 2: Installation instructions specify the use of copper conductors and approved wire connectors for 12 AWG. Keep the air vents of the thermostat clean and unobstructed to prevent harm. Make appropriate connections to the thermostat as per the provided diagram; the wires are non-polarized. Align and affix the base to the electrical junction box or optional adapter plate using two screws. The thermostat normally displays the actual ambient temperature. Proportional control allows the thermostat to modulate based on power usage. The thermostat saves the setpoint temperature and configuration selections permanently, even after power outages. To reset the thermostat, press specific buttons simultaneously. To change the thermostat installer configuration, press and hold a designated button for 5 seconds. Heating elements may have a protection device that activates when overheated, which can affect thermostat regulation.
• Page 3: Thermostat numérique électronique non programmable pour installations à la tension du réseau. Le thermostat 1E65-144 est conçu pour commander les systèmes de chauffage électriques, notamment : plinthes chauffantes, planchers radiants, plafonds radiants et convecteurs. Le thermostat ne peut être utilisé avec une charge résistive inférieure à 2 A, une charge résistive supérieure à 16,7 A, ou les installations commandées par un contacteur ou un relais. Alimentation : 120/240 V CA, 50/60 Hz, 2 A (résistive seulement). Températures affichées : 0 °C à 37 °C (32 °F à 99 °F). Afin de prévenir les décharges électriques, couper l’alimentation électrique au panneau de distribution principal avant les travaux d’installation ou de révision. Tout le câblage doit respecter les codes de l'électricité et règlements en vigueur. L'installation doit être effectuée par un maître électricien ou par un entrepreneur en chauffage et climatisation reconnu. Utiliser la plaque adaptatrice accessoire s’il est nécessaire de décaler les trous de montage de la boîte de raccordement. Desserrer la vis qui fixe le boîtier au socle du thermostat, puis pivoter le boîtier sur sa charnière et le détacher.
• Page 4: Installation requires the use of specific conductors and connection caps for 12 AWG wires. Ensure that the thermostat's air intakes are always clean and unobstructed to prevent damage. Wiring the thermostat should follow the provided diagrams. The thermostat should display the ambient temperature when set correctly. Adjustments include settings for heating and cooling modes, as well as temperature display options. The thermostat retains settings in permanent memory, even during power outages. To reset the thermostat, press specific buttons simultaneously. Thermal protection devices in heating elements may trigger during overheating, causing the thermostat to stop functioning temporarily. To illuminate the display, press the designated button. Configuration settings can be adjusted by holding a specific button for five seconds.