Home > CLIMATE MASTER > CLIMATE MASTER CXM2 Communicating Awc Thermostat Installation Guide

CLIMATE MASTER CXM2 Communicating Awc Thermostat Installation Guide

iGATE 2 COMMUNICATING (AWC) THERMOSTAT – IOM  
Diagnostics  
Refrigerant Valve Diagnostics (applies to Trilogy units)  
Hot Water Diagnostics (If Available)  
Data  
RV1 Status  
(QE models only)  
Description  
Data  
Unit  
Description  
Status of the RV1 (potable water heating)  
reversing valve.  
Control Voltage  
V
Hot water tank’s control voltage.  
Element Relay  
Status  
--  
Status of the hot water element relays.  
RV2 Status  
Status of the RV2 (heat/cool) reversing valve.  
Status of the heating electronic  
expansion valve.  
Current position of the heating electronic  
Hot Water  
Water Coil EEV1 Status  
Temperature/  
Upper Tank  
Temperature  
Lower Tank  
Temperature  
Current temperature at the upper  
element of the storage tank.  
F
Water Coil EEV1 Position expansion valve in steps.  
(0=fully closed, 1040 = fully open)  
Status of the cooling electronic  
Current temperature at the lower element  
of the storage tank.  
F
Air Coil EEV2 Status  
(QE models only)  
expansion valve.  
Current position of the cooling electronic  
expansion valve in steps.  
(0=fully closed, 1040 = fully open)  
Air Coil EEV2 Position  
(QE models only)  
Demand Hot Water (DHW) Diagnostics (If Available)  
Data  
Unit  
Description  
Hot Water  
Temperature of the potable hot water  
entering the potable hot water heat  
exchanger.  
Entering Water  
Temperature  
Hot Water  
F
Miscellaneous Diagnostics  
Data  
Unit  
Description  
gpm DHW flow rate.  
Temperature of the potable hot water  
Flow Rate  
Cabinet Ambient  
Temperature  
Communication  
Input Status2 –  
DH, G, H, NSB, O,  
OVR, W, Y1, Y2  
Compressor  
Ambient temperature in the unit’s  
compressor section.  
F
Hot Water  
Leaving Water  
Temperature  
leaving the potable hot water heat  
exchanger, returning to the  
iGate Smart Tank.  
F
Status of all communicated inputs from  
networked controls.  
Hot Water Pump  
Feedback  
Hot Water Pump  
Power  
Hot Water Pump  
Speed  
Current feedback signal from the  
DHW pump.  
Instantaneous power consumption of the  
DHW pump.  
%
W
%
Status of the compressor anti-short cycle  
delay timer.  
ASCD Timer  
sec  
V
Status2  
Control Voltage  
Unit’s control voltage.  
Current speed of the DHW pump.  
External  
Lockout status of network devices.  
Lockout Flag2  
Current calculation of heat of extraction  
(heating) or heat of rejection (cooling)  
to/from the loop depending on mode of  
operation.  
Fault History  
Heat of  
Extraction/  
Btuh  
Fault History stores and displays the five most  
recent fault or warning codes for the connected  
communicating control.  
Rejection1  
Input Status2 –  
ESD, G, H, HP, LP,  
NSB, O, OVR, W,  
Y1, Y2, CO  
Status of all physical inputs (switches and  
conventional thermostat).  
Output Status –  
Accessory Relay2  
1, 2  
Status of the configurable accessory relays.  
Output Status –  
Status of the Alarm relay.  
AL12  
Output Status –  
EH1, EH2  
Status of the electric heat outputs.  
Output Status –  
K1 (Fan, Loop  
Pump)2  
Status of fan enable/loop pump relay.  
Output Status –  
K2 (Fan Speed,  
HWG Pump)2  
Output Status1 –  
K3, K4, K7  
Status of fan speed/hot water generator  
pump relay.  
Status of configurable accessory relays.  
1. Applies to Trilogy only.  
2. Applies to Tranquility only.  
Part#: 97B0132N01 | Revised: Februar y 06, 2025  
PAG E : 1 7  
w w w. c l i m a te m a s te r. c o m  
GeneralDetails
NameCLIMATE MASTER CXM2 Communicating Awc Thermostat Installation Guide
MakeCLIMATE MASTER
LanguageEnglish
FiletypePDF (Download)
File size1.03 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...

CLIMATE MASTER CXM2 Communicating Awc Thermostat Installation Guide