Home > SMART TEMP > SMART TEMP SMT-131 Hotel Touchscreen Thermostat User Manual
×
- 1. Smt - 131 (Manual → Ver 2.7)
- 2. Revision History (Introduction → Thermostat Operation → Installation - Hvac Control → Dip Switch Settings → Wiring Hvac Control → Belimo 6 Way Valve)
- 3. Introduction (Thermostat Operation → Set Temperature → Fan)
- 4. Option 16 In The Installer Menu Permits You To Set The Smt-131 To Automatically Reset The Indoor Fan To Automatic Mode (cycle On And Off Wit… (Ventilation Mode → Make Up Room & Do Not Disturb Buttons → Installation - Hvac Control → System Design → Opening Wall Controller → Mounting Wall Controller)
- 5. Dip Switch Settings (Wiring - Hvac Control)
- 6. Caution
- 7. 10v Outputs (A1 Cool → A2 Heat → A3 Fan → Span → Time Interval → Direction)
- 8. Maximum Value (fan A3) Output Only (Belimo 6 Way Valve → Pipe Mode)
- 9. Klixon Mode / 2 Pipe (Ancillary Functions → Complete System Overview)
- 10. Occupancy Detection (Window Contact → Fault Indication)
- 11. Door Switch (Entering Or Exiting The Room → Door Left Open → Pir Input → Latched Occupancy Detection Logic)
- 12. Occupied Mode (Un-occupied Mode → Installer Option 'pir Input Delay' → Using A Pir Only For Occupancy Detection → Steps To Use The Smt-131 In Automatic Occupancy Detection Mode → Manual Occupancy Input → Doorbell)
- 13. Outside Door Station (Automatic Day Set Temperature → Modbus Wiring)
- 14. Modbus Data (Remote Temperature Sensors)
- 15. Installer Options Menu (Navigating Through The Installer Mode Settings → Option List Table)
- 16. High Temp Set Limit (Low Temp Set Limit → Dead Band → Fan Purge / Run On Period → Fan Span → Heat Span → Cool Span)
- 17. Unoccupied Fan Mode (Backlight → Temperature Calibration → Digital Input → Window Input Logic → Door Input Logic → Pir Input Delay)
- 18. Thermostat Response To Changes In Room (Firmware → Temperature Calibration → Factory Reset → Modbus Data Addendum 1)
- 19. Data Format (Protocol → Modbus Rtu (slave) → Byte Format → Device Id → Occupancy Status → Fan Status)
- 20. Read/write Room Temperature (Temperature Display → User Set Point High Limit → User Set Point Low Limit → Dead Band → Fan Purge Period → Auto Off Timer)
- 21. Unoccupied Fan Mode (Fan Speed Mode → Backlight → Digital Input Function → Reset Fan Mode → Belimo Mode → Modbus Address)
- 22. Modbus Control Of Outputs (Permitted Modes → Relay Status → 10v Heat Value → 10v Cool Value → Displaying)
- 23. Hide Both Mode And Fan Buttons
- 24. Permitted Modes (Fan Span → Window Input Logic → Window Input Delay → Door Input Logic → Door Input Delay → Unit Run Time Log)
- 25.
- 26. Specifications (Input Voltage → Operating Temperature → Operating Rh → Storage Temperature → Size → Display Size)
×
SMART TEMP SMT-131 Hotel Touchscreen Thermostat User Manual
| General | Details |
|---|---|
| Name | SMART TEMP SMT-131 Hotel Touchscreen Thermostat User Manual |
| Make | SMART TEMP |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.34 MB |

SMT-2W5 Smart Temp Wifi Thermostat Instruction Manual

Smart Temp SMT-850 Halo Thermostat User Guide

Smart Temp SMT-450 Flexistat WiFi Thermostat Instructions


MI-HEAT WT8 WiFi Smart Thermostat User Manual

OJ ELECTRONICS MWD5-1999-UAC3 Voice Control Wi-Fi Thermostat Instructions
Danfoss VICUQ24M Icon Programmable II Room Thermostat Installation Guide

Danfoss TP5001B-TP5001RF Programmable Room Thermostat User Guide

LUX TX1500E Programmable Thermostat Instruction Manual

GE Programmable CYNC Smart Thermostat User Guide

GLOBAL Touch Screen Thermostat HY08AC User Manual

Beca BHT-008 Heating Thermostat User Guide

GENERAL FH101S Underfloor Heating Thermostat User Manual

Milesight WT201 Smart Thermostat User Guide
Table of Contents
- 1. Smt - 131 - Manual →
- 2. Revision History - Introduction →
- 3. Introduction - Thermostat Operation →
- 4. Option 16 In The Installer Menu Permits You To Set The Smt-1... →
- 5. Dip Switch Settings - Wiring - Hvac Control →
- 6. Caution →
- 7. 10v Outputs - A1 Cool →
- 8. Maximum Value (fan A3) Output Only - Belimo 6 Way Valve →
- 9. Klixon Mode / 2 Pipe - Ancillary Functions →
- 10. Occupancy Detection - Window Contact →
- 11. Door Switch - Entering Or Exiting The Room →
- 12. Occupied Mode - Un-occupied Mode →
- 13. Outside Door Station - Automatic Day Set Temperature →
- 14. Modbus Data - Remote Temperature Sensors →
- 15. Installer Options Menu - Navigating Through The Installer Mo... →
- 16. High Temp Set Limit - Low Temp Set Limit →
- 17. Unoccupied Fan Mode - Backlight →
- 18. Thermostat Response To Changes In Room - Firmware →
- 19. Data Format - Protocol →
- 20. Read/write Room Temperature - Temperature Display →
- 21. Unoccupied Fan Mode - Fan Speed Mode →
- 22. Modbus Control Of Outputs - Permitted Modes →
- 23. Hide Both Mode And Fan Buttons →
- 24. Permitted Modes - Fan Span →
- 25. Page 25 →
- 26. Specifications - Input Voltage →





























