Home > SMART TEMP > SMART TEMP SMT-131 Hotel Touchscreen Thermostat User Manual
SMART TEMP SMT-131 Hotel Touchscreen Thermostat User Manual
Door Switch
The Door switch input (DS) is used by the SMT-131 for 3 functions.
1) To detect that the door has been opened and then closed to let somebody into or out
of the room.
2) To detect if the door has been left open.
3) To use as an occupancy or Auto-Off timer in training rooms or similar.
The SMT door switch input can be set for a Normally Open (switch open when door is closed) or
normally closed logic (switch closed when door is closed) or OFF (input not used). The Installer
logic in the SMT-131.
Entering or exiting the room.
Once the door is opened and then closed the SMT-131 will begin its occupancy detection process
using the PIR input described below. Based on the outcome of this process the SMT-131 will
remain on and permit guest interaction with the SMT-131 (adjust mode and set point for
example), or switch to “un-occupied” mode where the SMT-131 will substitute the guest set point
and mode for the installer pre-set values.
Door Left Open
When the door is left open for longer than the pre-set time (0 to 300 seconds) the SMT-131 will
automatically turn OFF. The text “OFF” will flash in the display to indicate that the remote door
(or window switch) is holding the SMT-131 in off mode. This is done to prevent energy waste by
trying to heat or cool an open room.
The SMT-131 will automatically restart once the door is closed.
PIR input
A PIR (passive infra-red) movement detector can be directly wired to the SMT-131 “PIR” input. As
movement is detected by the PIR it will send multiple On/Off pulses to the SMT-131 every time it
detects movement. The SMT-131 using this data (with or without a door switch) will determine
the occupancy status of the room and behave accordingly. Note, the PIR must be separately
powered, typically from a 12VDC supply. Consult the PIR manual for this information. Smart Temp
do not provide a PIR sensor, and suitable alarm PIR sensor is suitable.
Latched Occupancy Detection Logic
(Typically used in Hotel applications)
Latched occupancy detection requires a door
switch and PIR input to be wired and working.
When the door is first opened the SMT-131
instantly enters “Occupied Mode” where the
SMT-131 will permit the room occupant to set
their desired temperature and mode of
operation. Once the door is closed the SMT-131
will “look” for movement as detected by the PIR
sensor wired to the PIR input. If no movement is
seen within the installer pre-set seek time
(installer adjustable 1 to 15 minutes) the SMT-
131 will return to “Un-occupied mode” where the users temperature and mode will be replaced
with installer pre-set values. Should movement be detected within the installer pre-set seek time
the SMT-131 will Latch into “Occupied Mode” and no longer rely on continued movement within
Page 11
| General | Details |
|---|---|
| Name | SMART TEMP SMT-131 Hotel Touchscreen Thermostat User Manual |
| Make | SMART TEMP |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.34 MB |
(1 votes, average: 5.00 out of 5)
Loading...
SMT-2W5 Smart Temp Wifi Thermostat Instruction Manual
Smart Temp SMT-850 Halo Thermostat User Guide
Smart Temp SMT-450 Flexistat WiFi Thermostat Instructions
Provirtec TH-01 Smart Thermostat User Manual
STELPRO STZW402+ Electronic Thermostat Owner’s Manual
GENERAL LIFE ARUNA 304S RF Digital Room Thermostat User Manual
VENSTAR Fan Coil Thermostat T2100 / T2150 User Guide
GENERAL LIFE MITRA 220 Digital Room Thermostat User Manual
Honeywell T874H Multistage Thermostat Instruction Manual
SKYTECH 5320P Programmable Thermostat Fireplace Remote Control Instruction Manual
Honeywell RTHL3550 Non-programmable Thermostat Installation Guide
Olympia BS-812-P Programmable Thermostat User Manual
Honeywell RTH2510 Programmable Thermostat Owner’s Manual