Home > SMART TEMP > SMART TEMP SMT-131 Hotel Touchscreen Thermostat User Manual
×
- 1. Smt - 131 (Manual → Ver 2.7)
- 2. Revision History (Introduction → Thermostat Operation → Installation - Hvac Control → Dip Switch Settings → Wiring Hvac Control → Belimo 6 Way Valve)
- 3. Introduction (Thermostat Operation → Set Temperature → Fan)
- 4. Option 16 In The Installer Menu Permits You To Set The Smt-131 To Automatically Reset The Indoor Fan To Automatic Mode (cycle On And Off Wit… (Ventilation Mode → Make Up Room & Do Not Disturb Buttons → Installation - Hvac Control → System Design → Opening Wall Controller → Mounting Wall Controller)
- 5. Dip Switch Settings (Wiring - Hvac Control)
- 6. Caution
- 7. 10v Outputs (A1 Cool → A2 Heat → A3 Fan → Span → Time Interval → Direction)
- 8. Maximum Value (fan A3) Output Only (Belimo 6 Way Valve → Pipe Mode)
- 9. Klixon Mode / 2 Pipe (Ancillary Functions → Complete System Overview)
- 10. Occupancy Detection (Window Contact → Fault Indication)
- 11. Door Switch (Entering Or Exiting The Room → Door Left Open → Pir Input → Latched Occupancy Detection Logic)
- 12. Occupied Mode (Un-occupied Mode → Installer Option 'pir Input Delay' → Using A Pir Only For Occupancy Detection → Steps To Use The Smt-131 In Automatic Occupancy Detection Mode → Manual Occupancy Input → Doorbell)
- 13. Outside Door Station (Automatic Day Set Temperature → Modbus Wiring)
- 14. Modbus Data (Remote Temperature Sensors)
- 15. Installer Options Menu (Navigating Through The Installer Mode Settings → Option List Table)
- 16. High Temp Set Limit (Low Temp Set Limit → Dead Band → Fan Purge / Run On Period → Fan Span → Heat Span → Cool Span)
- 17. Unoccupied Fan Mode (Backlight → Temperature Calibration → Digital Input → Window Input Logic → Door Input Logic → Pir Input Delay)
- 18. Thermostat Response To Changes In Room (Firmware → Temperature Calibration → Factory Reset → Modbus Data Addendum 1)
- 19. Data Format (Protocol → Modbus Rtu (slave) → Byte Format → Device Id → Occupancy Status → Fan Status)
- 20. Read/write Room Temperature (Temperature Display → User Set Point High Limit → User Set Point Low Limit → Dead Band → Fan Purge Period → Auto Off Timer)
- 21. Unoccupied Fan Mode (Fan Speed Mode → Backlight → Digital Input Function → Reset Fan Mode → Belimo Mode → Modbus Address)
- 22. Modbus Control Of Outputs (Permitted Modes → Relay Status → 10v Heat Value → 10v Cool Value → Displaying)
- 23. Hide Both Mode And Fan Buttons
- 24. Permitted Modes (Fan Span → Window Input Logic → Window Input Delay → Door Input Logic → Door Input Delay → Unit Run Time Log)
- 25.
- 26. 400 66 Read Only Door Input Status 0: Open
- 27. Specifications (Input Voltage → Operating Temperature → Operating Rh → Storage Temperature → Size → Display Size)
×
SMART TEMP SMT-131 Hotel Touchscreen Thermostat User Manual
| General | Details |
|---|---|
| Name | SMART TEMP SMT-131 Hotel Touchscreen Thermostat User Manual |
| Make | SMART TEMP |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.34 MB |

SMT-2W5 Smart Temp Wifi Thermostat Instruction Manual

Smart Temp SMT-850 Halo Thermostat User Guide

Smart Temp SMT-450 Flexistat WiFi Thermostat Instructions


Robertshaw 4350 BJ Gas Thermostat Instructions

Micro Air ETRV EasyTouch RV Thermostat Instruction Manual

INKBIRD ITC-308-WIFI Digital Temperature Controller Thermostat Instruction Manual

WTE WT-100 Zigbee Thermostat User Manual

tuya BHT-005 Wifi Heating Thermostat User Manual

Honeywell Home FocusPRO Smart S200 Series Smart Thermostat User Guide

EMOS P5683 Surface Mount Thermostat Instructions

Milesight WT201 Airteq Smart Thermostat User Guide

WATTS WTC-ES Contact Thermostat User Manual

SALUS CONTROLS T105 Digital Programmable Thermostat User Guide
Table of Contents
- 1. Smt - 131 - Manual →
- 2. Revision History - Introduction →
- 3. Introduction - Thermostat Operation →
- 4. Option 16 In The Installer Menu Permits You To Set The Smt-1... →
- 5. Dip Switch Settings - Wiring - Hvac Control →
- 6. Caution →
- 7. 10v Outputs - A1 Cool →
- 8. Maximum Value (fan A3) Output Only - Belimo 6 Way Valve →
- 9. Klixon Mode / 2 Pipe - Ancillary Functions →
- 10. Occupancy Detection - Window Contact →
- 11. Door Switch - Entering Or Exiting The Room →
- 12. Occupied Mode - Un-occupied Mode →
- 13. Outside Door Station - Automatic Day Set Temperature →
- 14. Modbus Data - Remote Temperature Sensors →
- 15. Installer Options Menu - Navigating Through The Installer Mo... →
- 16. High Temp Set Limit - Low Temp Set Limit →
- 17. Unoccupied Fan Mode - Backlight →
- 18. Thermostat Response To Changes In Room - Firmware →
- 19. Data Format - Protocol →
- 20. Read/write Room Temperature - Temperature Display →
- 21. Unoccupied Fan Mode - Fan Speed Mode →
- 22. Modbus Control Of Outputs - Permitted Modes →
- 23. Hide Both Mode And Fan Buttons →
- 24. Permitted Modes - Fan Span →
- 25. Page 25 →
- 26. 400 66 Read Only Door Input Status 0: Open →
- 27. Specifications - Input Voltage →





























