SIEMENS RDH100RF/SET Room Thermostat Instruction Manual
NOTE:
You can press the OVERRIDE button on the receiver to manually switch ON/OFF for a faulty room unit
or transmission protocol.
DE
EN
FR
IT
Front View Receiver
NOTE:
You must re-execute the workflow for commissioning the set to reestablish a connection between the
room controller and receiver.
LED Signal Indicator
The signal is good when the
LED flashes green.
A flashing red LED indicates
that there is no signal.
LED Relay Indicator
Orange LED indicates relay is on.
Parameter setting
OVERRIDE Button
NL
ES
PT
CS
HU
PL
SV
FI
Press this button to overwrite transmitter
values.
RESET: Press the LEARN & OVERRIDE
button for 4 seconds to delete all transmitter
addresses.
Parameter setting mode
1. Press LEARN on the rear for 5 seconds until “P01” appears.
2. Press LEARN again and the parameter value on second line flashes
and is ready for adjustment.
LEARN Button
3. Adjust the parameter using setting knob.
4. Press LEARN once to confirm the setting.
5. Rotate the setting knob clockwise to next parameter and repeat steps 2
to 4.
6. Exit parameter setting mode by rotating the setting knob clockwise to
“End” and pressing LEARN button once.
Rear View Room
Unit
(Transmitter)
Press the button to learn a transmitter
address.
Parameters:
ñ
P01 Control behaviour: 2-position 1K / 2-position 0.5 K / PID fast / PID
slow (factory-setting)
ñ
ñ
P02 Maximum temperature range
P03 Minimum temperature range
ZH
TR
EL
RO
DA
TEST Button
Learn Button
Press and then release to
learn telegram
Used for testing transmission.
Press > 5 s to enter
parameter mode
Configuration instructions for the Siemens RDH100RF/SET
The transmitter RDH100RF and the receiver RCR100/433 are set to communicate (bonded) with each
other at the factory. If they fail it is necessary to re-bond the units due to the loss of communication,
please follow the below instructions.
1. Reset receiver by simultaneously pressing the LEARN & OVERRIDE button for 4 seconds.
2. Press and release the LEARN button. This sets the receiver to the learn mode.
3. Press and release the LEARN button on the back of the transmitter.
4. A green flashing or solid LED indicates a good signal, a red flashing or solid LED indicates no
signal.
5. To test transmission, press the TEST button on the transmitter, switches the relay on in
the receiver regardless of temperature. The RF TEST symbol appears on the thermostat display.
6. An orange LED indicates that the relay is on.
A6V101035988_en--_d
2018-06-21
Subject to alteration
Siemens Smart Infrastructure / HVAC Products
| General | Details |
|---|---|
| Name | SIEMENS RDH100RF/SET Room Thermostat Instruction Manual |
| Make | SIEMENS |
| Language | English |
| Filetype | PDF (Download) |
| File size | 3.23 MB |
(1 votes, average: 5.00 out of 5)
Loading...
SIEMENS RDZ100ZB Zigbee Room Thermostat Owner’s Manual
SIEMENS RDG400 Room Thermostat Instruction Manual
SIEMENS M3182 Room Thermostat Instruction Manual
SIEMENS RDS120-B Smart Thermostat Instructions
SIEMENS Powers Controls TH 192-3 Series Day Night Vent Room Thermostat Instruction Manual
SIEMENS RDY2000BN BACnet Commercial Thermostat User Manual
SIEMENS RDH100RF/SET Wireless Room Thermostat with LCD User Guide
SIEMENS RS485 Flush Mounted Room Thermostat User Manual
SIEMENS RDG260KN Room Thermostat Instruction Manual
SIEMENS RDF660MB Flush Mount Room Thermostat Instruction Manual
GENERAL LIFE MITRA HT10 RF Digital Room Thermostat User Guide
Wengart WG603 Home Smart Thermostat User Guide
STN855W WiFi Digital Programmable Thermostat Instruction Manual
DELTA DORE Tybox 5701FP Pilot Wire Thermostat User Guide
Garza 400610 Digital Programmable Thermostat User Manual
Beca BHT-7000 Smart Knob Thermostat User Manual
Smartica HY608W 3A Wifi Digital Heating Thermostat User Manual
hansgrohe 15763003 Shower Select Thermostat Instruction Manual
Danfoss M30 React Radiator Thermostat Installation Guide
hyco PT01 Programmable Thermostat Instruction Manual