Home > HEATIT > heatit Z-Temp2 Wireless Thermostat Instruction Manual

heatit Z-Temp2 Wireless Thermostat Instruction Manual

5

1. INTRODUCTION

Firmware 1.2

Heatit Z-Temp2 is a battery-operated thermostat designed for use with

waterbased heating systems. Used in combination with the Heatit

Z-Water regulator you can control your heating system with a Z-Wave

primary controller/gateway. All communication between the Heatit

Z-Temp2 and the controlled device is 100% wireless.

HEATIT

Z-TEMP2

Installers manual

01.12.2020

Ver 2020-B

2. STATEMENT REGARDING PRODUCT FROM MULTIPLE

MANUFACTURERS

Please read this before installation

This device may be used with all devices certiﬁed with the Z-Wave Plus™

certiﬁcate and should be compatible with such devices produced by

other manufacturers. Every primary controller is diﬀerent depending on

the manufacturer, their target audience and intended

use/application. Please review the functionalities implemented by

the primary controller you intend to use with our Z-Wave Plus

certiﬁed device to ensure that it provides the necessary controls

to take full advantage of our product’s capabilities.

3. BEHAVIOR WITHIN THE Z-WAVE NETWORK

TABLE OF CONTENTS

This product can be operated in any Z-Wave network with other Z-Wave

certiﬁed devices from other manufacturers. All non-battery-operated

nodes within the network will act as repeaters regardless

of manufacturer to increase reliability of the network. On delivery,

the device does not belong to any Z-Wave network. The device

needs to be added to an existing network to communicate with

the devices of this network. Devices can also be removed from

a network. Both adding and removing process are initiated by the primary

controller of the Z-Wave network.

Introduction

Statement regarding products from multiple

manufacturers

Behavior within the Z-Wave™ network

Quick Start

Installation

Add/Remove

6.1 Method 1 Standard (manual)

6.2 Method 2 SmartStart (automatic)

Factory Reset

This controller will enter a mode for adding or removing devices. Please

refer to your primary controller/gateway manual on how to turn your

controller into add or remove mode. The device can only be added or

removed from the network if the primary controller is in add/remove

mode. When the device is removed from the network, the device will

revert to factory default settings.

Compability/ Principles for regulation

Information shown in display

10 Hysteresis (DIF)

11 Childlock - Lock

12 Inverted output

13 Standby and main screen

14 Z-Wave QR-Code / DSK

15 Security

4. QUICK START

4.1. Install the batteries (as stated in the technical speciﬁcation).

4.2. Install the device on a ﬂat vertical surface using screws or

double-sided tape

16 Node Information Frame

17 Associations

18 Conﬁguration parameters

19 Operating the device

20 Supported Command Classes

4.3. Set the controller/gateway in add mode (security/non-

security).

4.4. Press the link button 3 times in a rapid sequence.

4.5. The thermostat will display“INC”when the thermostat is

successfully included.

Product information

NB! If adding/removing fails, Err (error) will appear.

5. INSTALLATION

Use a large ﬂathead screwdriver to remove the back cover.

Fix the unit to the wall by double-sided tape, screws or installed

on top of a Euro wall box.

Make sure the mounting surface is clean and dry.

Then install 3x AA batteries (alkaline) in the device’s battery-holder.

NB! Be careful to when installing batteries, ensuring the polarity of

the batteries is in accordance with the printing in plastic.

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	heatit Z-Temp2 Wireless Thermostat Instruction Manual
Make	HEATIT
Language	English
Filetype	PDF (Download)
File size	0.22 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Comments are closed.

HEATIT Instructions & User Manuals

heatit Z-TRM6 DC Z Wave Electronic Thermostat Instruction Manual

HEATIT Z-TRM3 Thermostat User Guide

Heatit Z-TEMP2 Thermostat Installation Guide

heatit Z-TRM3 WiFi Thermostat Instruction Manual

HEATIT Z-Temp3 is a Battery Operated Thermostat Instruction Manual

4512673 Heatit ZM Thermostat 16A User Guide

HEATIT Z-TRM6 Matt Z-Wave Thermostat User Guide

HEATIT 54 304 59 DIN Smart Thermostat Installation Guide

HEATIT 54 305 41 WiFi6 Thermostat Installation Guide

HEATIT Z-TEMP3 Thermostat User Guide

Get the free PDF manual for the heatit Z-Temp2 Wireless Thermostat Instruction Manual and access setup steps, usage instructions, and troubleshooting tips. 👉 View online or download now to keep your thermostat running smoothly!

Heatit Z-Temp2 Manual: Questions and Answers

Heatit Z-Temp2 specifications

Power supply	3 x AA batteries (1,5V)
Differential	0,3°C to 3,0°C (default 0,5°C)
Operating temperature	5°C to 40°C
Humidity	Max. 85% RH
IP rating	IP 21
Communication	Z-Wave

Full specifications, page 5

What does the Heatit Z-Temp2 report when power is restored after an outage?

It sends a notification command to indicate idle state, plus humidity and temperature reports. Instruction Manual, p. 5

What does the link button do on the Heatit Z-Temp2?

Press it three times in rapid sequence to add the thermostat to a Z-Wave network. Instruction Manual, p. 1

Where is the battery compartment located on this thermostat?

Behind the back cover, which you remove with a large flathead screwdriver. Instruction Manual, p. 1

How do you know if the Heatit Z-Temp2 was successfully added to the network?

The display shows INC when inclusion is complete. If it fails, Err appears instead. Instruction Manual, p. 1

Heatit Z-Temp2 compared with other Heatit thermostats

Specification	Heatit Z-Temp2	Heatit 54 304 DIN	Heatit Z-TRM3	Heatit Z-Temp3 is
Power supply	3 x AA batteries (1,5V)	230VAC 50Hz	230VAC 50/60Hz	2.7VDC to 3.3VDC
Differential	0,3°C to 3,0°C (default 0,5°C)	0.3°C to 3.0°C (default 0.5°C)	0.3°C to 3.0°C (default 0.5°C)	0.3°C to 3.0°C (Default 0.5°C)
IP rating	IP 21	IP21	IP 21	IP21
Communication	Z-Wave	Z-Wave, 868.4MHz	Z-Wave	Z-Wave, 868.4MHz