heatit Z-Temp2 Wireless Thermostat Instruction Manual
7. FACTORY RESET
By pressing and holding the link button for 20 seconds, the thermostat
will perform a complete factory reset. rES will be displayed.
NB! Please use this procedure only when the primary controller/
gateway is missing or otherwise inoperable.
8. COMPABILITY / PPRRIINNCCIIPPLLEESS FFOORR RREEGGUULLAATTIIOONN
Water based heating
The thermostat uses temperature readings retrieved from the internal
sensor. Heatit Z-Temp2 is designed to work together with water based
heating solutions. Heatit recommends using Heatit Z-Temp2 together
with Heatit Z-Water. These two products allow for an advanced water
based heating solution by using a Z-Wave enabled controller. This
is a“wire-free”solution which save both time and money. All the
communication between Heatit Z-Temp2 and the controlled device is
wireless. The range can be extended using Heatit Z-Repeater or any other
device that supports routing. This makes our water based solutions a
good addition to your existing or new home automation system.
Electrical heating
Heatit Z-Temp2 could also be used in situations where a traditional
electrical thermostat is not suited. The battery-operated thermostat can
be used together with Heatit Z-Relay or any other relay device installed
in a remote location. Rehabilitation could be done using this solution to
avoid unnecessary wiring.
6. ADD/REMOVE
There are two ways to add your devices in a Z-Wave network.
6.1. Method 1: standard (manual)
Please refer to your primary controller/gateway manual on how to
enter add/remove mode. The device
the network if the primary controller i
When the primary controller/gateway
the link button on the thermostat 3 ti
ISPLAY
eens.
emperature readout or relative
e humidity and measured
utton while display is active.
The temperature and humidity can be calibrated using parameter
4 and 5 respectively. When childlock is active, there will displayed
a lock icon adjacent to the Celsius icon.
6.2. Method 2: SmartStart (automat
Please refer to your primary controller
supported by the controller. SmartStart enabled products can be added
into a Z-Wave network by scanning the Z-Wave QR-Code present on the
product with a controller providing SmartStart inclusion. No further action
is required and the SmartStart product will be added automatically within
10 minutes of being switched on in the network vicinity.
Secondary screen
This screen displays the setpoint temperature when the thermostat is in
heating mode. When the thermostat mode is turned OFF, the thermostat
will not use this display. To turn ON or OFF the thermostat you need to
hold center button for 10 seconds, or use Z-Wave command Basic or
Thermostat mode.
Enter SmartStart modus from your primary controller.
With the batteries for the devices taken out of the device. Scan the QR-
code on back of the device, then follow the gateway instructions.
If the device already belongs to a network, follow the removing process
before adding it in your network. Otherwise, the adding of this device will
fail. When the device is removed from the network,
Connecting to an external relay
After the device is added to your Z-Wave gateway you will need to link
the thermostat to the device that is going to control the heating. This
is done by using association groups from the thermostat’s root device
(EP0) with Group 3 (ON/OFF Control) towards your actuator device (using
Multichannel or Single channel, based on the controlled device type.
the device will revert to factory settings.
*To set associations in your primary controller/gateway, please refer to
your primary controller/Z-Wave gateway for more information.
10. HYSTERESIS (DIF)
You can make changes to the hysteresis in the thermostat via the
parameter. This means that you can changes the hysteresis from
0,3°C up to max 3,0°C. Default is 0,5°C.
| General | Details |
|---|---|
| Name | heatit Z-Temp2 Wireless Thermostat Instruction Manual |
| Make | HEATIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.22 MB |
(1 votes, average: 5.00 out of 5)
Loading...
heatit Z-TRM6 DC Z Wave Electronic Thermostat Instruction Manual
HEATIT Z-TRM3 Thermostat User Guide
Heatit Z-TEMP2 Thermostat Installation Guide
heatit Z-TRM3 WiFi Thermostat Instruction Manual
HEATIT Z-Temp3 is a Battery Operated Thermostat Instruction Manual
4512673 Heatit ZM Thermostat 16A User Guide
HEATIT Z-TRM6 Matt Z-Wave Thermostat User Guide
HEATIT 54 304 59 DIN Smart Thermostat Installation Guide
HEATIT 54 305 41 WiFi6 Thermostat Installation Guide
HEATIT Z-TEMP3 Thermostat User Guide
GENERAL LIFE 270S RF Room Thermostat User Manual
Danfoss UT 72 Thermostat Installation Guide
Honeywell Home FocusPRO S200 Series Smart Thermostat User Guide
NEOMITIS RTE7SD Mains Powered Digital 7 Day Programmable Room Thermostat Instruction Manual
tado 104388 Smart Thermostat
Danfoss DEVIreg 330 Electronic Thermostat Installation Guide
Honeywell TL6120 5-2 Electric Heating Programmable Thermostat User Guide
Honeywell PRO3000 Series Non-Programmable Digital Thermostat Instruction Manual
SALUS RT310RF Digital Wireless Central Heating Room Thermostat User Manual
ADAX VG11 Digital Thermostat User Guide