HEATIT Z-TRM6 Matt Z-Wave Thermostat User Guide

1

2

STATEMENT REGARDING PRODUCTS FROM MULTIPLE  

MANUFACTURERS  

Please read this before installation  

5. Set the primary controller in add mode (security/non  

security).  

FACTORY RESET  

TECHNICAL DATA  

Enter the menu by holding the Center button for about 5  

seconds, navigate in the menu with the ”+” button til you see  

FACT. Press the Center button until you see “-- --” blinking in  

the display, then hold for about 5 seconds to perform a reset.  

You may also initiate a reset by holding the Right and Center  

buttons for 60 seconds.  

HEATIT  

Protocol  

Chip  

Z-Wave Plus, 868.4MHz  

Z-Wave 800 chip  

230VAC 50Hz  

3600W 16A (resistive load)  

Contactor recommended for  

loads above 13A  

16A  

6. Hold the Center button until “OFF” is shown in the display  

(approx. 5 seconds).  

This device may be used with all devices certified with the  

Z-Wave Plus™ certificate and should be compatible with  

such devices produced by any manufacturer. Every primary  

controller is different depending on the manufacturer, their  

target audience and intended use/application. Please review  

the functionalities implemented by the primary controller you  

intend to use with our Z-Wave Plus certified device to ensure  

that it provides the necessary controls to take full advantage of  

our product’s capabilities.  

Rated voltage  

Max load  

Z-TRM6  

Quick Guide  

7. Press the ”+” button once to reach “CON”, and hold until the  

display shows a rotating light pattern.  

TO PRODUCT  

DOCUMENTS  

8. The thermostat will display “INCL” when the thermostat is  

successfully added. NB! If adding/removing fails, Err (error)  

will appear.  

Max current  

Power consumption  

Power regulator  

Article no.  

Doc. version  

Doc. date  

When either of these procedures has been performed, the  

thermostat will perform a complete factory reset. The device  

will display “RES” for 5 seconds while performing a factory reset.  

When “RES” is no longer displayed, the thermostat has been  

reset.  

<2W  

54 305 66  

54 305 68  

2023-A  

01.07.2023  

Time cycle 0 to 30 min.  

Ambient temperature 5°C to 40°C  

Temperature range 5°C to 40°C  

Storage temperature -30°C to 70°C  

Hysteresis  

Humidity  

ADD/REMOVE  

The primary controller/gateway has a mode for adding or  

removing devices. Please refer to your primary controller  

manual on how to set the primary controller in add/remove  

mode. The device may only be added or removed from the  

network if the primary controller is in add/remove mode. When  

the device is removed from the network, it will NOT revert to  

factory settings.  

INSTALLATION  

0.3°C to 3.0°C (default 0.5°C)  

10% to 85% RH  

Please use this procedure only when the network primary  

controller is missing or otherwise inoperable.  

Installation must be done by a qualified electrician in  

accordance with national building codes. Before installation,  

disconnect the power to the device from the mains. During  

installation of the device, power to the device must be  

disconnected AT ALL TIMES!  

Compatible with NTC-  

sensor with values  

Range RF  

6.8, 10, 12, 15, 22, 33, 47 or 100kΩ @ 25°C  

Min. 40 meter  

Max. 2.5mm² 2Nm  

IP21  

CHOICE OF SENSOR  

The thermostat has multiple sensors and sensor modes. This  

lets you configure the thermostat to work correctly in most  

installations.  

Screw terminals  

IP Code  

Size (LxWxH)  

CONNECTIONS  

Max tightening torque terminal screws: 2Nm.  

84 x 84 x 45.5mm  

An always listening node must be powered continuously and  

reside in a fixed position in the installation to secure the routing  

table. Adding the device within a 2 meter range from the  

gateway can minimize faults during the Interview process.  

Available temperature sensors:  

Approvals  

Z-Wave Plus v2, CE, Nemko  

White RAL 9003  

54 305 66  

Black matt  

54 305 68  

To access the terminal screws, hold the sides of the display and  

gently pull outwards to detach the front piece.  

F

Floor sensor  

MAINTENANCE  

A

Internal room sensor  

There are two ways to add the device to a Z-Wave network.  

AF  

A2  

A2F  

Internal room sensor + Floor sensor  

External room sensor  

The product is maintenance-free.  

Indoor use only.  

INTRODUCTION  

Standard (Manual)  

Heatit Z-TRM6 is an electronic thermostat designed for  

electrical heating. The thermostat can be controlled through  

your Z-Wave™ network or via the buttons on the front. The  

thermostat has a user friendly interface.  

External room sensor + Floor sensor  

Add/remove mode is indicated on the device by rotating  

LED segments on the display. It indicates this for 90 seconds  

until a timeout occurs, or until the device has been added to/  

removed from the network. Configuration mode can also be  

cancelled by performing the same procedure used for starting  

Configuration mode.  

45.5mm  

PWER Power regulator mode (no sensor used)  

22mm 23.5mm  

50mm  

NOTE: Some types of floor require that a floor sensor is  

connected in order to limit the floor temperature to a maximum  

of 27°C (check the manual from the floor manufacturer). When  

the thermostat is used in AF or A2F the floor limiter FHI is  

automatically set to 27°C. When using any other sensor type  

(A, F or A2) the minimum and maximum limits are 5°C and 40°C  

respectively.  

Heatit Z-TRM6 has 3 modes; Heat - Cool and Eco.  

The thermostat fits in standard European junction boxes and  

may be used with most System 55 frames. It has a sturdy metal  

frame for secure fastening on the junction box. The thermostat  

has one built-in room temperature sensor. Two additional  

external temperature sensors may also be connected.  

1. Hold the Center button for 5 seconds.  

The display will show “OFF”.  

Floor sensor  

NTC type 6.8, 10, 12, 15, 22, 33, 47 or 100kΩ.  

Default 10kΩ.  

2. Press the ”+” button once to see “CON” in the display.  

3. Start the add/remove device process in your primary  

controller.  

External sensor NTC type 6.8, 10, 12, 15, 22, 33, 47 or 100kΩ.  

DISPLAY ICONS  

Default 10kΩ.  

Heatit Z-TRM6 has active power metering and it gives you real  

time information about your power consumption. It also allows  

you to set the power metering value manually in case of  

connection with a contactor.  

N

Power connection (Neutral) 230VAC.  

Heating cable N connection.  

ICON  

DESCRIPTION  

4. Start the configuration mode on the thermostat by holding  

the Center button for approximately 2 seconds.  

Heating N  

L

This icon will be displayed while the relay is on and  

the thermostat is in either Heating or Eco mode.  

Power connection (Live) 230VAC.  

Heating cable L connection.  

Heating L  

The device is now ready for use with default settings.  

This icon will be displayed while the relay is on and  

the thermostat is in Cooling mode.  

The thermostat can be set up with multiple associations  

and can be used as a master thermostat. It can also control  

external relays and wall plugs.  

Next, position the thermostat and mount it into the junction  

box using 2 screws. Position the thermostat front over the part  

mounted in the junction box, then carefully press the front until  

it clicks into place. In order to get power metering values, the  

load needs to be connected to both heating L + N.  

NB! When the device is removed from the gateway, the  

parameters are not reset. To reset the parameters, see  

”Factory reset”.  

This icon shows the current signal strength.  

We develop and design our products according in accordance with our strict quality  

requirements (ISO 9001) and environmental requirements (ISO 14001). All electrical  

installations must be carried out by an authorized electrical installer. The product  

must be installed in accordance with our installers manual and national building  

codes. Any wrongful installation, misuse, damage of the product, is not covered  

under warranty. Updated documentation is available at www.heatit.com and/or  

documents.heatit.com. Heatit Controls AB can not be held liable for any type of  

errors or omittances in our product information. Product specifications may change  

without further notice.  

The thermostat can withstand a load of max. 16A/3600W at  

230VAC. We recommend a contactor for loads above 13A.  

If inclusion fails, please perform a ”remove device” process and  

try again. If inclusion fails again, please see “Factory reset”.  

QUICK START  

1. Switch off the mains voltage (disable the fuse).  

2. Open the junction box.  

SmartStart (Automatic)  

SmartStart enabled products may be added to a Z-Wave  

network by scanning the Z-Wave QR-Code on the product  

if your primary controller supports SmartStart inclusion. No  

further action is required and the SmartStart product will be  

added automatically after being powered on within range of the  

primary controller.  

3. Connect the wires according to the description above  

Optional: Connect external wired sensors.  

4. After verifying the connections, switch on the mains voltage.  

Org. doc. 01.07.2023  

Heatit Controls AB  

l

Läkarvägen 4, 454 31 BRASTAD, SWEDEN  

Phone: +47 61 18 77 77 l post@heatit.com – www.heatit.com  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	HEATIT Z-TRM6 Matt Z-Wave Thermostat User Guide
Make	HEATIT
Language	English
Filetype	PDF (Download)
File size	0.27 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• HEATIT

HEATIT Z-TRM6 Matt Z-Wave Thermostat User Guide Overview

Summary of Contents

• Page 1: statement regarding products from multiple manufacturers please read this before installation set the primary controller in add mode (security/non security) factory reset technical data the device may be used with all devices certified with the Z-Wave Plus™ certificate and should be compatible with such devices produced by any manufacturer. installation must be done by a qualified electrician in accordance with national building codes. the thermostat has multiple sensors and sensor modes. the product is maintenance-free. the thermostat can withstand a load of max. 16A/3600W at 230VAC.
• Page 2: Erklæring vedrørende produkter fra ulike produsenter Les dette før installasjon Denne enheten kan brukes sammen med andre enheter sertifisert med Z-Wave Plus™-sertifikatet. Hver gateway er forskjellig avhengig av produsent, målgruppe og tiltenkt bruk/applikasjon. Hold midtknappen inne til du ser OFF i displayet (ca. 5 sek.). Trykk på + knappen. CON vises i displayet. Gå inn i menyen ved å holde midtknappen inne i ca. 5 sekunder. Displayet vil vise INCL når termostaten har blitt inkludert. Når en av disse prosedyrene er utført, vil termostaten utføre en fullstendig tilbakestilling til fabrikkinnstillinger. Produktet skal installeres av autorisert installatør i henhold til norske byggforskrifter. Heatit Z-TRM6 er en elektronisk termostat designet for elektrisk gulvvarme.