Home > HEATIT > WIFI Temp2 Battery Operated Thermostat Installation Guide

WIFI Temp2 Battery Operated Thermostat Installation Guide

4

1. INTRODUCTION

Heatit WiFi thermostat is an electronic thermostat for electrical

underﬂoor heating. The thermostat has a simple user interface and

can be easily programmed via the capacitive buttons. The color screen

displays an accessible user interface. The thermostat has a built-in WiFi

chip that allows you to control it from a user-friendly app. The ”Heatit

WiFi”app is available on Google Play and in the App Store. Works

with Amazon Alexa and Google Home (pending). If you are installing

multiple thermostats in the same house, you may copy the settings

from one thermostat to the next. This simpliﬁes installation.

01.10.2021

HEATIT WIFI

Installers manual

Ver 2021-A

Heatit WiFi thermostat 16A is equipped with a single-pole switch and

ﬁts into most common frames (e.g. System 55, Elko RS16, Schneider

Exxact). The thermostat can withstand a load of max 16A/3600W

at 230VAC. We recommend a contactor for loads above 13A. The

thermostat may be connected to an external sensor.

The thermostat is designed for electrical heating.

2. INSTALLATION

Installation must be done by a qualiﬁed electrician in accordance with

the national building codes. Before installation, disconnect any power

to the device mains. During installation of the device, power to the

device must be disconnected AT ALL TIMES!

TABLE OF CONTENTS

1. Introduction

2. Installation

3. Startup

4. Symbols

4.1 Operation mode

4.2 Heating/Cooling active

4.3 Note

5. Controls

6. Standby and main screen

7. Menu items

8. Operation mode

9. Weekly schedule

10. Heatit WiFi zones

11. Advanced settings

12. WiFi settings

Release the front cover by pressing e.g. a screwdriver gently into the

ejector latch at the bottom of the thermostat.

Now connect the wires to the thermostat terminals:

13. Phone applications

14. Product info

Power connection (Live)

LOAD (N)

LOAD (L)

Heating Cable connection (Neutral)

Heating Cable connection (Live)

Power connection (Neutral)

Pilot Wire (if applicable)

PILOT

SENSOR

Floor temp sensor, NTC type

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	WIFI Temp2 Battery Operated Thermostat Installation Guide
Make	HEATIT
Language	English
Filetype	PDF (Download)
File size	0.75 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Comments are closed.

HEATIT Instructions & User Manuals

heatit Z-TRM6 DC Z Wave Electronic Thermostat Instruction Manual

HEATIT Z-TRM3 Thermostat User Guide

Heatit Z-TEMP2 Thermostat Installation Guide

heatit Z-TRM3 WiFi Thermostat Instruction Manual

HEATIT Z-Temp3 is a Battery Operated Thermostat Instruction Manual

4512673 Heatit ZM Thermostat 16A User Guide

HEATIT Z-TRM6 Matt Z-Wave Thermostat User Guide

HEATIT 54 304 59 DIN Smart Thermostat Installation Guide

HEATIT 54 305 41 WiFi6 Thermostat Installation Guide

HEATIT Z-TEMP3 Thermostat User Guide

Get the free PDF manual for the WIFI Temp2 Battery Operated Thermostat Installation Guide and access setup steps, usage instructions, and troubleshooting tips. 👉 View online or download now to keep your thermostat running smoothly!

Heatit Temp2 Manual: Questions and Answers

Heatit Temp2 specifications

Power supply	230VAC 50Hz
Floor temperature limit	5°C - 40°C (concrete) or 5°C - 27°C (wood)
Setpoint range	5°C to 40°C
Differential	0.2°C to 2°C (0.5°C standard)
Sensor	Floor temp sensor, NTC type
IP rating	IP 21

Full specifications, page 4

How do I return to the main screen on my Heatit Temp2

Hold the left button for two seconds from any menu location. Installation Guide, p. 2

Can I use the Heatit Temp2 with a wooden floor and what temperature limit applies

Yes, but a floor sensor must be connected. The maximum floor temperature limit is 27°C for wooden floors. Installation Guide, p. 2

What do the three buttons on Heatit Temp2 do

Left button goes up or returns to main screen. Center button confirms selections and opens menus. Right button goes down. Installation Guide, p. 2

Heatit Temp2 compared with other Heatit thermostats

Specification	Heatit Temp2	Heatit Z-TRM3	Heatit Z-TRM6 DC Z Wave	Heatit 54 304 DIN
Power supply	230VAC 50Hz	230VAC 50/60Hz	230VAC 50Hz	230VAC 50Hz
Setpoint range	5°C to 40°C	5°C to 40°C	5°C to 40°C	2°C to 40°C
Differential	0.2°C to 2°C (0.5°C standard)	0.3°C to 3.0°C (default 0.5°C)	0.3°C to 3.0°C (default 0.5°C)	0.3°C to 3.0°C (default 0.5°C)
IP rating	IP 21	IP 21	IP21	IP21