EcoNet RETST800SYS Smart Thermostat User Guide
Thermostat Settings
Installer Settings
Go to Menu > Settings > Installer (tap and hold) > Thermostat.
Thermostat
Furnace
AC/HP
Air Handler
Defaults
Warning! These settings are to be used
by a qualified HVACcontractor ONLY
BACK
Thermostat Settings
Thermostat Brand – The EcoNet Smart Thermostat will automatically
populate when the system starts up by reading the equipment’s model data card.
Thermostat Brand
Rheem
Aux Heat Hold Off Time
Filter Check Hour
Anticipator
Auto
9 am
0
Aux. Heat Hold Off Time – This setting is designed to keep the auxiliary heat
off for a duration of time determined by the user. The time periods are:
BACK
• Auto: The thermostat will energize Aux Heat once the temperature has
reached 1 full degree beyond the heat set point. Also if the heating
system is not maintaining the set point using the heat pump alone.
• 1-60 min: The number of minutes the system will keep the Aux Heat
from coming on even when the space temperature goes beyond 1 degree.
Filter Check Hour – The time of day when the EcoNet Smart Thermostat will
check the air filter status.
Anticipator – Gives the user the ability to accurately control the system
from overshooting in the Heating and the lag of delivering conditioned air in
the cooling mode. When set to 0 the system will use the factory default and
recommended rate of equipment cycling to maintain comfort. Increasing
the number will slow down the system, causing longer cycles. Reducing the
number will make the system react quicker, shortening the equipment cycle.
The higher the negative
number the faster the system
will cycle off, increasing the
number of times the system
cycles off in an hour.
The higher the positive
number the longer the system
will stay cycled on, lowering
the number of times the
system cycles off in an hour.
-5
-4
-3
-2
-1
1
2
3
4
5
0
Factory set default
and
recommended
rate of equipment
cycling.
Air Handler Settings
Installer Settings
Go to Menu > Settings > Installer (tap and hold) > Air Handler.
Thermostat
Furnace
AC/HP
Air Handler
Defaults
Warning! These settings are to be used
by a qualified HVACcontractor ONLY
BACK
Air Hander Settings
Electric Heater Size – If electric strip heaters are installed in the air handler
Electric Heater Size
None
you will need to select the appropriate size.
EXV Superheat Offset
0° F
O Input Fan Control
Off
Off
Off
Electric Heat Airflow Select – Four choices available. Refer to air handler
installation instructions for air flow settings.
Aux #1 Config
Aux #2 Config
Filter Type
N.O.
N.O.
Media
BACK
See pages 28-29 for the G Input and AUX Input details. These settings are the
same for both furnace and air handler.
> Return to Table of Contents
EcoNet® Smart Thermostat User Guide 31
| General | Details |
|---|---|
| Name | EcoNet RETST800SYS Smart Thermostat User Guide |
| Make | EcoNet |
| Language | English |
| Filetype | PDF (Download) |
| File size | 6.45 MB |
(1 votes, average: 5.00 out of 5)
Loading...
EcoNet UETST800SYS Smart Thermostat User Guide
EPH CONTROLS CP4 Programmable RF Thermostat User Manual
EPH CONTROLS 2023-03-10 RFR-RF Room Thermostat Instruction Manual
GENERAL LIFE HT250S Digital Room Thermostat User Manual
Haswill Electronics AL8010H Thermostat User Guide
tecnoswitch Raffaello 230 TE215VU Electronic Recessed Thermostat User Guide
SITERWELL GS368 Smart Programmable Thermostat User Manual
Smartica HY608W 3A Wifi Digital Heating Thermostat User Manual
Honeywell RTH230B Thermostat Installation Guide
CIELO BM101WA Breez Max Smart Thermostat Installation Guide
GENERAL LIFE Senna 330S RF Wireless Room Thermostat User Manual