Home > sinope > sinope TH1134ZB Smart Line Voltage Thermostat Installation Guide

sinope TH1134ZB Smart Line Voltage Thermostat Installation Guide

2

YOUR TH1134ZB/HC THERMOSTAT

TECHNICAL SPECIFICATIONS

Operatlng voltage: 120 / 208 / 240 Vac, 60 Hz

TH1134ZB/HC Thermostat

Maximum load:

16.7 A / 2000 W @ 120 Vac

16.7 A / 4000 W @ 240 Vac

Resistive load only.

Full-color display

Minimum load:

1.25 A / 300 W @ 240 Vca

1.25 A / 150 W @ 120 Vca

Heating setpoint range: 41°F to 86°F (5°C to 30°C)

Display range: 32°F to 99°F (0°C to 50°C)

Storage: -4°F to 122°F (-20°C to 50°C)

Operation: 32°F to 122°F (0°C to 50°C)

Resolution: 0.5°C ( 1°F)

TH1134ZB/HC

Installation Guide

Touch-sensor

buttons

Smart Line Voltage Thermostat

Protocol: Zigbee 3.0

Frequency: 2.4 GHz

Transmission power: +20 dBm

Receiver sensitivity: -108 dBm

Compatible with an electric heating system such as:

• Baseboard heater [short cycle]

• Convector [short cycle]

• Fan-forced convector [long cycle)

• Radiant ceiling heating

Touch control

Warnings

Special CO/ ALR solderless connectors must be used

when connecting with aluminum conductors.

The installation of this thermostat must be performed by a certified electrician

and comply with the national and local electrical codes and regulations.

INSTALL YOUR THERMOSTAT

Use the connectors provided to connect the thermostat wires to the wires in the

electrical box. Use the screws to secure the thermostat to the electrical box.

Unlock and lift the

thermostat cover.

Make sure that the

breakers for your

heating system are

off at the main

electrical panel.

Three-wire installation

Electrical

Make sure to firmly tighten the

wire connectors for a secure

connection. A loose connection

can be a fire hazard.

panel

N ^{(120 V)}

L1 ^{(240 V)}

3/4"

To install wire connectors,

you must:

White - Neutral/Line 1

Insert the two wires into the wire nut so that their

copper ends are parallel.

Red - Load

Black - Line 2

Turn the wire connector clockwise until there is

strong tension.

Replace the cover

and lock.

Power up the thermostat.

Pull on the threads to make sure they are secure,

leaving no gaps between them. * If the threads

seem to come loose, repeat the process.

* Improperly installed electrical wires could burn the wire

connectors.

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	sinope TH1134ZB Smart Line Voltage Thermostat Installation Guide
Make	sinope
Language	English
Filetype	PDF (Download)
File size	0.56 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Comments are closed.

sinope Instructions & User Manuals

sinope TH1134ZB-HC Smart Line Voltage Thermostat Owner’s Manual

sinope Smart Low Voltage Thermostat TH1400WF Installation Guide

sinope Smart Floor Heating Thermostat TH1310WF Installation Guide

sinope TH1124NP Non Programmable Thermostat for Electric Heating Owner’s Manual

sinope TH1300ZB-C4 3600W Smart Floor Heating Thermostat Installation Guide

sinope TH1400NP Non Programmable Low Voltage Thermostat Installation Guide

sinope TH1500ZB Smart Double Pole Thermostat Installation Guide

sinope TH1500WF Smart Double Pole Thermostat Installation Guide

Get the free PDF manual for the sinope TH1134ZB Smart Line Voltage Thermostat Installation Guide and access setup steps, usage instructions, and troubleshooting tips. 👉 View online or download now to keep your thermostat running smoothly!

Sinopé TH1134ZB Manual: Questions and Answers

Sinopé TH1134ZB specifications

Display range	32°F to 99°F (0°C to 50°C)
Storage temperature	-4°F to 122°F (-20°C to 50°C)
Radio frequency	2.4 GHz
Communication	Zigbee 3.0

Full specifications, page 1

How do I know if Sinopé TH1134ZB is connected to the gateway successfully?

A connection confirmation message appears on the screen. If connection fails, 'Failure' will display instead. Installation Guide, p. 2

Can Sinopé TH1134ZB work with any Zigbee gateway, or does it require the GT130?

It works with the GT130 gateway or any compatible Zigbee system. Refer to the installation guide for compatible gateway details. Installation Guide, p. 2

How do I connect Sinopé TH1134ZB to the GT130 gateway for the first time?

Initiate a connectivity session and connect the thermostat to the network.

Press the RF signal button on the GT130 gateway; the indicator light will start flashing
Press and simultaneously on the thermostat
Wait for the connection confirmation message on the screen Installation Guide, p. 2

Sinopé TH1134ZB compared with other Sinopé thermostats

Specification	Sinopé TH1134ZB	Sinopé TH1134ZB-HC	Sinopé TH1500ZB	Sinopé TH1400WF
Display range	32°F to 99°F (0°C to 50°C)	32 °F to 99 ° (0 °C to 50 °C)	0 °C to 50 °C (32 °F to 99 °F)	0 ˚C to 70 ˚C (32 ˚F to 99 ˚F)
Storage temperature	-4°F to 122°F (-20°C to 50°C)	-4 °F to 122 °F (-20 °C to 50 °C)	-20 °C to 50 °C (-4 °F to 122 °F)	-20 ˚C to 50 ˚C (-4 ˚F to 122 ˚F)
Radio frequency	2.4 GHz	2.4 GHz	2.4 GHz	2.4 GHz