sinope TH1400NP Non Programmable Low Voltage Thermostat Installation Guide

1

2

INSTALL YOUR THERMOSTAT  

Unlock and lift the  

thermostat cover.  

If necessary, mark and drill the  

1

3

Depending on the heating system,  

insert each wire into its terminal  

and screw firmly. (See connection  

layouts outlined in the following  

pages.)  

2

appropriate fastening holes, using the  

installation template. If needed, use  

the wall anchors included.  

TH1400NP  

Installation Guide  

Non-Programmable  

Low Voltage Thermostat (24 Vac)  

4

Use the provided screws and  

wall anchors to fix the  

thermostat base on the wall.  

6

Power up the thermostat.  

5

Replace back and lock the  

thermostat cover.  

Set  

AUXILIARY OUTPUT  

WIRING LAYOUT  

The thermostat provides an auxiliary heating output that  

can act as a second stage of heating when controlling  

ambient temperature.  

Electric baseboard  

Hot water valve  

120 V  

240 V  

347 V  

24 V  

24 Vac  

Valve  

normally open  

If the room temperature is too far from the setpoint or the  

main stage of heating has difficulties raising the  

temperature, the auxiliary output activates the secondary  

heating source to reach the set temperature.  

C

Electric baseboard  

R

W1  

W2  

Both outputs can control different types of heating load and  

can be configured in the user settings.  

S1  

For use in floor or ambient  

mode with floor limit.  

Floor sensor  

S2  

Not required for ambient  

mode alone.  

Electric floor heating with electric  

baseboard on the 2nd heating stage  

Electric floor heating  

Floor sensor  

Electric baseboard  

CONNECTION OF THE FLOOR SENSOR  

(OPTIONAL)  

Only for control applications in floor (F) mode or with floor limit.  

Increasing or lowering the temperature  

To adjust the temperature, press or  

. The requested temperature  

will blink to confirm the new setpoint.  

When installing your floor heating system: add a  

second sensor in the floor and store the tip in the  

thermostat housing. This additional sensor can be  

plugged in and used as a replacement without  

haltering your floor heating system.  

Set  

Sensor  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	sinope TH1400NP Non Programmable Low Voltage Thermostat Installation Guide
Make	sinope
Language	English
Filetype	PDF (Download)
File size	0.33 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• sinope

sinope TH1400NP Non Programmable Low Voltage Thermostat Installation Guide Overview

Summary of Contents

• Page 1: Install your thermostat by unlocking and lifting the thermostat cover. Mark and drill the appropriate fastening holes using the installation template. Insert each wire into its terminal and screw firmly, following the connection layouts. Use the provided screws and wall anchors to fix the thermostat base on the wall. Power up the thermostat and replace back and lock the thermostat cover. The thermostat provides an auxiliary heating output that can act as a second stage of heating. The auxiliary output activates the secondary heating source if the room temperature is too far from the setpoint. Both outputs can control different types of heating load and can be configured in the user settings. For control applications in floor mode or with floor limit, a floor sensor can be connected. To adjust the temperature, press the appropriate buttons, and the requested temperature will blink to confirm the new setpoint.
• Page 2: Parameters that can be controlled from the device include cycle length, temperature format, control mode, and backlight control. The thermostat features two temperature control modes: A mode for ambient temperature regulation and F mode for floor temperature regulation. To access the menu, lower the setpoint to its minimum and hold the button for 10 seconds. The maximum floor temperature limit is only visible in A mode, while the minimum floor temperature limit is also only visible in A mode. The circulator pump's anti-seizure feature activates the main output during 1 minute every 24 hours to prevent the pump from seizing. Operating voltage is 24 Vac with a maximum load of 1 Amp. The troubleshooting guide includes information on the E1F code, which indicates that the thermostat is in Floor mode without a connected sensor. The setpoint range is from 5 °C to 36 °C (41 °F to 97 °F), and the display range is from 0 °C to 70 °C (32 °F to 99 °F). The warranty covers defects in material and workmanship for a 3-year period under normal use. The product is compatible with various heating systems, including baseboard heaters, fan-forced convectors, and hydronic heating systems.