EUROSTER 4040 Smart Programmable Thermostat User Manual
EUROSTER 4040 Smart – INSTALLATION AND OPERATION MANUAL 3
5. INSTALLATION
5.1. Safety rules
CAUTION!
•
Prior to the commencement of any installation works read this manual
carefully! Incorrect installation and improper use may lead to serious hazards
to users or other persons and result in property damage!
Prior to mounting or dismantling the set make sure that the heating/cooling
system is de-energized.
Voltages hazardous to life may be present on thermostat connecting cables
(power supply phase voltage), therefore only qualified technicians may install
the thermostat!
•
•
•
•
The electric connections performed and cables used shall be adequate to the
applied loads and must conform to all requirements!
Do not install the set in rooms with increased humidity; protect it against
water and other liquids!
•
•
Do not install any set showing signs of mechanical damage!
The thermostat is not a safety component. Additional protection devices must
be used in systems prone to the risk of damage due to the failure of control
systems!
•
•
The device is not intended for use by children!
Should there be any problem with the proper operation of the thermostat,
please contact your technician or the manufacturer!
CAUTION!
Euroster 4040 RX Smart Receiver and a heat emitting device must be powered from
the same phase of the power system.
5.2. Selecting the place of thermostat installation
The thermostat is designed for indoor installation. No cables are connected to the thermostat,
thus it can be placed anywhere. To ensure fully efficient operation of the thermostat, please
make sure that the following recommendations regarding the location of the thermostat are
observed:
•
•
Locate the thermostat at the height of approximately 1.5 m above the floor
Avoid places exposed to intense sunlight, situated near heating or cooling devices,
directly by doors, windows, and other similar locations, where the temperature
measurement could be easily disturbed by external conditions.
Avoid places with poor air circulation, e.g. behind furniture.
•
•
Avoid moist places due to the negative effect of moisture on the service life of the
device.
5.3. Installation of the receiver
Insert the receiver into the 230 V power socket, as close as possible to the controlled device.
The Wi-Fi module is built-in inside the receiver, thus you should ensure that the receiver is
within the range of the Wi-Fi signal. You should also check the strength of the radio signal
between the thermostat and the receiver.
5.4. Insertion and replacement of batteries
Place the batteries in the thermostat while observing their correct polarity. There are
installation markings in the battery compartment. Then install (snap) the thermostat onto the
base.
CAUTION! Use only alkaline AAA batteries to power the thermostat. Do not use
rechargeable batteries because their voltage is lower and their effective time is
shorter.
It is recommended to replace batteries before each heating season.
| General | Details |
|---|---|
| Name | EUROSTER 4040 Smart Programmable Thermostat User Manual |
| Make | EUROSTER |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.33 MB |
(1 votes, average: 5.00 out of 5)
Loading...
EUROSTER 2006TXRX Wireless Programmable Thermostat Installation Guide
EUROSTER 2026TXRX Air Conditioning Thermostat Instruction Manual
Beca BAC-7000 Smart Knob Thermostat User Guide
dahua TRV1 Smart Radiator Thermostat Owner’s Manual
sinope TH1134ZB-HC Smart Line Voltage Thermostat Owner’s Manual
WHITE-RODGERS 1F51N-619 Low Voltage Evaporative Cooler Thermostat Instruction Manual
ENGO CONTROLS E25-BATW Zig Bee 868MHz Smart Thermostat User Guide
ENGO CONTROLS EFAN-24W Fan Coil Thermostat User Guide
Honeywell Non-Programmable Thermostat RTH5160D1003 Installation Guide
EMERSON 1F83C-11NP Single Stage Thermostat Owner’s Manual
hansgrohe AXOR STARCK Concealed Thermostat with Shut Off Valve Instruction Manual
Ferono FTH-30 Universal Thermostat Instruction Manual