Glow-Worm SRT 50-2 Climastat Select Programmable Room Thermostat User Manual

1

2

3.2  

Display  

4.2.3 Frost protection  

Note  

1

Safety  

Validity: Competent person  

> Turn the rotary knob to set the  

required target room temperature.  

> Press the rotary knob to confirm the  

setting, or wait for three seconds  

until the change is automatically  

applied.  

1.1  

Intended use  

1.2.2 Risk caused by inadequate  

qualifications  

1

2

3

4

5

The frost protection function is only  

active if the boiler is operating.  

In the event of inappropriate or improper  

use, damage to the product and other  

property may arise.  

The room temperature control is designed  

to control a heating installation with eBUS  

interface according to the room tempera-  

ture.  

The following work must only be carried  

out by competent persons who are suffi-  

ciently qualified to do so:  

− Set-up  

− Dismantling  

− Installation  

− Start-up  

− Inspection and maintenance  

− Repair  

− Decommissioning  

> Proceed in accordance with current  

technology.  

The frost protection function activates the  

boiler if the environmental temperature in  

the room in which the product is installed  

falls below 5 °C.  

> For a longer period away from home,  

observe the information on frost protec-  

tion in the boiler’s operating instruc-  

tions.  

Climastat Select  

¬ The display shows the changed target  

room temperature for three seconds.  

¬ The display switches to the basic dis-  

play.  

6

SRT 50/2  

Note  

Validity: End user  

If a time programme is active,  

the target room temperature is  

only changed temporarily,  

depending on the system con-  

trol specifications.  

1

2

3

4

Boiler in heating mode  

Boiler in domestic hot water mode  

Boiler maintenance required  

Control connected to gateway (only in the  

control type for the remote control)  

Fault in the boiler  

Intended use includes the following:  

− observance of the operating instruc-  

tions included for the product and any  

other installation components  

4.3  

Troubleshooting  

In the event of faults, the corresponding  

fault messages are shown in the display.  

5

6

Validity: Competent person  

1.2.3 Risk of material damage  

caused by using an  

Current room temperature  

Condition: The product is set to the control  

type for remote control, The system control  

does not allow the temperature to be  

changed.  

Fault  

Cause  

Measure  

Intended use includes the following:  

− observance of accompanying operat-  

ing, installation and maintenance  

instructions for the product and any  

other system components  

− installing and setting up the product in  

accordance with the product and sys-  

tem approval  

3.3  

CE marking  

unsuitable tool  

Display is  

Power supply Check the  

switched off. has been dis- boiler’s  

connected. power sup-  

ply.  

The CE marking shows that the  

products comply with the basic  

requirements of the applicable  

> Use the correct tool.  

> Turn the rotary knob.  

1.3  

Regulations (directives,  

laws, standards)  

en  

Faults in the control type for the room  

temperature control  

¬

is displayed.  

directives as stated on the declaration of  

conformity.  

The declaration of conformity can be  

viewed at the manufacturer’s site.  

¬ If the heating mode is activated,  

the target room temperature spec-  

ified by the system control is  

shown on the display for three  

seconds.  

> Observe the national regulations,  

standards, directives, ordinances and  

laws.  

The required The thermo-  

room temper- static valves  

ature has not on the heat-  

Turn the ther-  

mostatic  

valves on the  

radiators until  

they are fully  

open.  

Intended use also covers installation in  

accordance with the IP class.  

been  

reached.  

ing element  

are not set  

correctly.  

4

Operation  

2

Notes on the  

Validity: End user  

− The target room temperature  

cannot be changed via the  

product.  

documentation  

This product can be used by children  

aged from 8 years and above and per-  

sons with reduced physical, sensory or  

mental capabilities or lack of experience  

and knowledge if they have been given  

supervision or instruction concerning use  

of the product in a safe way and under-  

stand the hazards involved. Children must  

not play with the product. Cleaning and  

user maintenance work must not be car-  

ried out by children unless they are super-  

vised.  

4.1  

Operating concept  

The required Internal time  

room temper- period in the  

ature has not boiler does  

Check the  

time periods  

in the boiler.  

0020314824_02  

You use the rotary knob to operate the  

product.  

> Turn the rotary knob anti-clockwise or  

clockwise to decrease or increase the  

value, or to set parameters.  

2.1  

Observing other applicable  

documents  

¬ If the heating mode is deactivated  

by the system control, off is then  

shown on the display for three  

seconds.  

Publisher/manufacturer/supplier  

been  

reached.  

not permit  

heating  

mode.  

Vaillant Group UK LTD  

Nottingham Road  

> You must observe all operating instruc-  

tions enclosed with the system compo-  

nents.  

Belper-Derbyshire | DE56 1JQ  

Telephone 01773 824639  

Technical helpline 0330 100 7679  

After sales service 0330 100 3142  

www.glow-worm.co.uk  

The required Heat curve or Consult a  

room temper- flow temper-  

− The target room temperature  

cannot be changed via the  

product.  

competent  

person.  

> Press the rotary knob to access a set-  

ting or to confirm a setting.  

ature is  

exceeded.  

ature has  

been set  

2.2  

Storing documents  

¬ The display switches to the basic  

display.  

incorrectly.  

4.2  

Operating and display  

functions  

> Keep this manual and all other applica-  

The boiler  

Normal  

No measure  

ble documents safe for future use.  

display does behaviour for required.  

not show any some system  

The current room temperature is dis-  

played in the basic display.  

2.3  

Validity of the instructions  

4.2.2 Setting the domestic hot  

water temperature  

Validity: End user + Competent person  

symbol indi-  

cating that a  

control is  

configura-  

tions.  

These instructions apply only to:  

Any other use that is not specified in  

these instructions, or use beyond that  

specified in this document, shall be con-  

sidered improper use. Any direct commer-  

cial or industrial use is also deemed to be  

improper.  

4.2.1 Setting the target room  

temperature  

Product  

Article number  

0010038664  

connected.  

Note  

Climastat Select  

In the control type for remote con-  

trol, the domestic hot water tem-  

perature can only be controlled via  

the communication unit or the con-  

trol for the boiler.  

Heating  

Heating  

To deactivate  

the heating  

mode, set  

Condition: The product is set to the control  

mode is  

mode can  

only be acti-  

vated/ deacti- the lowest  

vated via the target room  

active even  

though this  

has been  

type for room temperature control.  

3

Product description  

> Turn the rotary knob.  

The product is a room temperature con-  

trol.  

Caution!  

¬

is displayed.  

¬ The set target room temperature  

flashes on the display.  

deactivated  

on the boiler.  

product.  

temperature  

on the prod-  

uct.  

Improper use of any kind is prohibited.  

Condition: The product is set to the control  

type for room temperature control, the boiler  

can generate domestic hot water, the domes-  

tic hot water function is activated on the  

product  

3.1  

Product design  

1.2  

General safety information  

Fault in the  

boiler.  

In the boiler’s  

operating  

instructions,  

check  

whether you  

can eliminate  

the fault  

yourself or  

contact a  

competent  

person.  

> Turn the rotary knob to set the  

required target room temperature.  

> Press the rotary knob to confirm the  

setting, or wait for three seconds until  

the change is automatically applied.  

¬ The display shows the changed  

target room temperature for three  

seconds.  

flashes.  

Validity: End user  

1

2

1.2.1 Danger caused by improper  

operation  

> Press the rotary knob.  

¬

is displayed and the domestic  

hot water temperature that is cur-  

rently set on the control flashes in  

the display (factory setting: 60 °C).  

Improper operation may present a danger  

to you and others, and cause material  

damage.  

> Carefully read the enclosed instructions  

and all other applicable documents,  

particularly the “Safety” section and the  

warnings.  

> Only carry out the activities for which  

instructions are provided in these oper-  

ating instructions.  

¬ The display switches to the basic  

display.  

> Turn the rotary knob to change the  

domestic hot water temperature (38–  

65 °C).  

> Press the rotary knob to confirm the  

setting, or wait for three seconds until  

the change is automatically applied.  

¬ The display switches to the basic  

display.  

Fault in the  

eBUS con-  

nection to the person.  

boiler.  

Consult a  

competent  

flashes  

and Err is  

shown in the  

display.  

1

2

Display  

Rotary knob  

Condition: The product is set to the control  

type for remote control, The system control  

allows the temperature to be changed  

> Turn the rotary knob.  

¬

is displayed.  

¬ The current target room tempera-  

ture flashes on the display.  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Glow-Worm SRT 50-2 Climastat Select Programmable Room Thermostat User Manual
Make	Glow-Worm
Language	English
Filetype	PDF (Download)
File size	0.18 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• Glow-Worm

Glow-Worm SRT 50-2 Climastat Select Programmable Room Thermostat User Manual Overview

Summary of Contents

• Page 1: Display Frost protection Safety Intended use The frost protection function is only active if the boiler is operating. The room temperature control is designed to control a heating installation with eBUS interface according to the room temperature. The following work must only be carried out by competent persons who are sufficiently qualified to do so: set-up, dismantling, installation, start-up, inspection and maintenance, repair, decommissioning. The frost protection function activates the boiler if the environmental temperature in the room falls below 5 °C. If a time programme is active, the target room temperature is only changed temporarily, depending on the system control specifications. In the event of faults, the corresponding fault messages are shown in the display.
• Page 2: Room temperature control is set to factory settings. The product must be installed by a qualified competent person while complying with existing regulations. Only qualified electricians may carry out the electrical installation. The maximum length of the eBUS cable is 125 m. Connection cables with 230 V and eBUS cables must be routed separately beyond a length of 10 m. The domestic hot water function must be activated before setting the domestic hot water temperature. Clean the casing with a damp cloth and a little solvent-free soap. Do not dispose of the product with household waste; instead, hand it in to a collection center for waste electrical or electronic equipment. The competent person who installed the product is responsible for the disposal of the packaging. Inform the end user how to handle the product and answer any questions they may have.