ENGO CONTROLS ESIMPLE230W Non-Programmable Wired Thermostat User Guide

1

2

INTRODUCTION:  

Proper thermostat location  

ESIMPLE230W / ESIMPLE230B is a surface-mounted, wired room thermostat  

intended for surface heating / cooling, characterized by high thermal inertia. The  

room setpoint temperature is set with a knob. Thanks to the built-in algorithms,  

it offers much better temperature control accuracy than traditional mechanical  

thermostats.  

ENGO SIMPLE - Non-programmable, wired thermostat  

Product Compliance  

This product complies with the following EU Directives: 2014/30/EU, 2014/35/EU,  

2011/65/EU.  

Please note!  

For the thermostat to work properly, it must be installed in a suitable place.  

Preferably approx. 150 cm above floor level, away from sources of heat or cold. In  

addition, the thermostat should not be installed behind curtains or other  

obstacles or in places with high humidity, as this will prevent an accurate  

measurement of the temperature in the room. It is not recommended to install  

the thermostat on an outside wall, in a draft or in a place where it will be exposed  

to direct sunlight.  

ESIMPLE230W  

ESIMPLE230B  

SAFETY INFORMATION:  

Use in accordance with national and EU regulations. Use the device only as  

intended, keeping it in a dry condition. The product is for indoor use only. Please  

read the entire manual, before installation or use.  

QUICK GUIDE  

INSTALLATION:  

Ver. 1  

Release date: VIII 2022  

Installation must be performed by a qualified person with appropriate  

electrical qualifications, in accordance with the standards and regulations in  

force in a given country and in the EU. The manufacturer is not responsible for  

non-compliance with the instructions  

Diagram for connecting the thermostat to the underfloor heating  

control box.  

WARNING:  

THERMOSTAT  

ESIMPLE230W/  

ESIMPLE230B  

For the entire installation, there may be additional protection requirements,  

which the installer is responsible for.  

N

L

SL  

Package content  

Producer:  

Distributor:  

QL CONTROLS Sp z o.o. Sp. k.  

43-262 Kobielice  

ul. Rolna 4  

Engo Controls S.C.  

43-200 Pszczyna  

ul. Górnośląska 3E  

N

L

INPUT_1  

S

L

1

N

L

INPUT_2  

SL2  

Control box  

ECB08M230  

Polska  

Polska  

THERMOSTAT  

THERMOSTAT  

LED  

LED  

Legend:  

Thermostat ESIMPLE230W / ESIMPLE230B  

ENGO SIMPLE DIAL THERMOSTAT  

L, N - power supply 230V  

ESIMPLE230W  

ESIMPLE230B  

SL - 230V output signal from thermostat  

Producent:  

www.engocontrols.com  

Engo Controls S.C.  

43-200 Pszczyna  

ul. Górnośląska 3E  

Polska  

Skrócona instrukcja  

Dystrybutor:  

QL CONTROLS Sp o.o. Sp. k.  

43-262 Kobielice  

Ver. 1  

Data wydania:  

z

V

2022  

ul. Rolna  

Polska  

4

www.engocontrols.com  

SL1...SL8 - 230V control input in the control box  

Mounting screws  

Manual  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	ENGO CONTROLS ESIMPLE230W Non-Programmable Wired Thermostat User Guide
Make	ENGO CONTROLS
Language	English
Filetype	PDF (Download)
File size	0.15 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• ENGO CONTROLS

ENGO CONTROLS ESIMPLE230W Non-Programmable Wired Thermostat User Guide Overview

Summary of Contents

• Page 1: INTRODUCTION: Proper thermostat location is crucial for accurate temperature measurement. The ESIMPLE230W / ESIMPLE230B is a surface-mounted, wired room thermostat designed for surface heating/cooling with high thermal inertia. The room setpoint temperature is adjusted using a knob, offering better temperature control accuracy than traditional mechanical thermostats. This product complies with EU Directives: 2014/30/EU, 2014/35/EU, 2011/65/EU. For optimal performance, install the thermostat approximately 150 cm above floor level, away from heat sources, curtains, and high humidity areas. SAFETY INFORMATION: Use the device in accordance with national and EU regulations and only as intended, keeping it dry. Installation must be performed by a qualified person in accordance with applicable standards and regulations. The manufacturer is not responsible for non-compliance with installation instructions. There may be additional protection requirements for the installation, which the installer must address.
• Page 2: Wall mounting LED light indications The status of the thermostat is determined by the LED, illuminating in different colors. During wire connections, ensure they are not connected to the 230V AC power supply. Additional functions of the thermostats can be switched on or off by switches located on the front cover. The heating or cooling mode is based on the setting of the switches under the knob. The position of the HEAT slider indicates the heating mode, while the COOL slider indicates the cooling mode. Temperature control range is 5 – 30°C. The thermostat allows selection of the mode of controlling room temperature by TPI algorithm or by hysteresis +/-0.5°C. The TPI algorithm is designed for underfloor heating to maintain room temperature precisely. Dimensions of the thermostat are 80 x 80 x 22 mm.