ENGO CONTROLS EONE-BATW, EONE-BATB Internet Controlled Thermostat User Guide

1

2

Wireless communication diagram  

Installation thermostat in the app  

Product Compliance  

Make sure your router is within range of your smartphone. Make sure you are connected to the Internet.  

This will reduce the pairing time of the device.  

This product complies with the following EU  

Directives: 2014/30/EU, 2014/35/EU, 2014/53/  

EU, 2011/65/EU  

Internet controlled thermostat, ZigBee  

ZigBee 3.0  

WI-FI 2.4GHz  

STEP 1 - DOWNLOAD ENGO SMART APP  

SAFETY INFORMATION:  

Use in accordance with national and EU  

regulations. Use the device only as intended,  

keeping it in a dry condition. The product is for  

indoor use only. Please read the entire manual,  

before installation or use.  

Gateway  

Download the ENGO Smart app from Google Play or Apple App Store and install it on your smartphone.  

EGATEZB  

EONE-BATW/B  

EONE-BATW  

EONE-BATB  

ZigBee 3.0  

Quick Guide  

WARNING:  

This product must be used with a ZigBee  

gateway (purchased separately). Thermostat  

programming is done by ENGO Smart app.  

or  

or  

Works with  

Powered By  

Ver. 7.4  

Release date: VII 2024  

Soft:  

EMOD-ZB  

EREL-12ZB  

Relay  

ECB62-ZB  

STEP 2 - REGISTER THE NEW ACCOUNT  

Control box  

Module  

ZigBee: v1.0.12  

MCU: v2.0.9  

Product advantages:  

GET IT ON  

To register a new account, please follow the steps below:  

Available on the  

Built-in Li-Ion 3,7V Battery  

Connection description  

Legend:  

1

2

3

4

Communication in the ZigBee 3.0 standard  

ZigBee 3.0  

Battery powered  

EONE-BATW/B  

S1  

A multitude of functions available from  

ENGO Smart / Tuya Smart application  

Producer:  

Engo Controls sp z o.o. sp. k.  

Rolna 4  

Temperature sensor  

Li-lon  

3.7V  

43-262 Kobielice  

Poland  

S1-S2 Input for additional sensor  

S1, S2 Thermostat input for ext. temperature sensor  

Connection with ZigBee 3.0 network  

NTC  

S2  

ENGO  

ENGO binding function (devices connection  

in Online and Offline mode)  

BINDING  

Click„Register”  

to create new account.  

Enter your e-mail  

address to which the  

Enter the verification code Then set the login  

password.  

www.engocontrols.com  

Connection with WiFi 2.4GHz network  

Products sold separately  

received in the email.  

verification code will Remember that you only  

be sent.  

have 60 seconds to enter  

the code!!  

LCD Icon Description + Button Description  

INTRODUCTION:  

STEP 3 - CONNECT THE THERMOSTAT TO ZigBee  

1

2

3

1. Current humidity reading  

2. Current/Setpoint temperature  

3. Clock  

EONE-BAT is a surface-mounted room thermostat which works over ZigBee technology. It has a built-in  

humidity sensor and a minimum/maximum setpoint temperature limiting function. The EONE-BAT has the  

ability to work in heating or cooling modes. The unique feature of this thermostat is the possibility of wireless  

control over ENGO binding function. In order to have the ability to controll wirelessly, EONE-BAT needs to be  

used with ENGO Smart / TUYA Smart mobile application and EGATE-ZB internet gateway (sold separately).  

„ENGO binding” function provides wireless and direct connection to the receivers (e.g. ECB62-ZB control box,  

EMOD-ZB module or EREL-12ZB relay) over the gateway. After adding to the mobile app, thermostat offer  

more functions, e.g. push notifications or possibility of programming time schedules.  

4

4. Temperature unit  

5. Heating indicator (icon is animating when  

there is heating demand)  

6. Cooling indicator (icon is animating when  

there is cooling demand)  

7. Schedule mode icon  

8. Temporary override mode  

9. External/Floor or Occupancy sensor  

10. Button lock  

1

2

3

16  

15  

14  

SET  

5

6

7

8

9

11. Holiday mode  

12. Settings icon  

13. Battery indicator  

14. Receiver binding indicator  

15. ZigBee network connection indicator  

16. Settings icon / temperature settings  

Make sure ZigBee Gateway has been added to the Engo  

Smart app. Press and hold the and buttons on the  

thermostat until the display shows„PA”. Then release the keys.  

The pairing mode will be started up.  

Thermostat counts the time  

back (180s).  

12  

10  

1. “Up”Button  

2. ”OK”Button  

3. ”Down”Button  

13  

11  

Technical Informations  

Power supply  

Charging connector  

Temperature range  

Display temperature accuracy  

Control algorithm  

Built-in Li-Ion 3,7V Battery  

USB type C, 5V DC  

Button description  

1

2

3

Change the parameter value up  

5,0°C - 45,0°C  

Change the parameter value down  

0,5°C  

Manual/Schedule mode - short button press (Online mode)  

Enther the installer parameters- hold 3 seconds  

Turn OFF/ON thermostat - hold 5 seconds  

Enter the pairing mode - hold 5 seconds  

TPI or Histeresis (from 0,1°C to 2°C)  

ZigBee 3.0 2,4GHz  

Communication  

S1/S2 multifunctional input  

IP protection class  

Floor temp sensor, external air sensor, occupancy sensor  

IP30  

+

Enter binding mode - hold 5 seconds  

In„Zigbee devices list”  

go„Add devices”.  

Wait for the message "End"  

to appear on the thermostat  

screen.  

Enter the gateway interface.  

Dimension [mm]  

90 x 90 x 14 mm  

Factory reset - hold until the FA message appears  

Lock/Unlock thermostat keys - hold 3 seconds  

Heating/Cooling mode change - hold 3seconds  

+

+

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	ENGO CONTROLS EONE-BATW, EONE-BATB Internet Controlled Thermostat User Guide
Make	ENGO CONTROLS
Language	English
Filetype	PDF (Download)
File size	0.53 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• ENGO CONTROLS

ENGO CONTROLS EONE-BATW, EONE-BATB Internet Controlled Thermostat User Guide Overview

Summary of Contents

• Page 1: Wireless communication diagram Installation thermostat in the app Make sure your router is within range of your smartphone. Make sure you are connected to the Internet. This product complies with the following EU Directives: 2014/30/EU, 2014/35/EU, 2014/53/EU, 2011/65/EU Download the ENGO Smart app from Google Play or Apple App Store and install it on your smartphone. Use in accordance with national and EU regulations. Use the device only as intended, keeping it in a dry condition. The product is for indoor use only. This product must be used with a ZigBee gateway (purchased separately). Thermostat programming is done by ENGO Smart app. EONE-BAT is a surface-mounted room thermostat which works over ZigBee technology. It has a built-in humidity sensor and a minimum/maximum setpoint temperature limiting function. Make sure ZigBee Gateway has been added to the Engo Smart app. Press and hold the buttons on the thermostat until the display shows PA. Then release the keys. Enter the pairing mode - hold 5 seconds.
• Page 2: Installer parameters Binding thermostat with the ECB62-ZB wireless control box Make sure that the ECB62-ZB control box and thermostat are in the same ZigBee network and the POWER LED lights up blue. In order to correctly link thermostat with the control box, first select the zone in the control box with the SELECT button. The LED will flash green with the previously selected zone - binding process has started. If the thermostat indicates wrong temperature, you can correct it by max 3.5°C. Minimum heating/cooling temperature that can be set is 5°C. This function helps to keep the floor warm, even if there is no heating demand from the room thermostat. After successful binding operation, End message will be displayed. To enter installer parameters press and hold button for 3 seconds. When the thermostat is binded with the module, the relay will turn off after 50 minutes if the communication between the devices is lost.