Home > ENGO CONTROLS > ENGO CONTROLS EONE-BATW, EONE-BATB Internet Controlled Thermostat User Guide
ENGO CONTROLS EONE-BATW, EONE-BATB Internet Controlled Thermostat User Guide
Installer parameters
4
5
6
Binding thermostat with the ECB62-ZB wireless control box
Default
value
Pxx
Function
Value
Desription
Make sure that the ECB62-ZB control box and thermostat are in the same ZigBee network (they are added to
the same gateway) and the POWER LED lights up blue.
12h
24h
12 hour
24 hour
Heating
P01
Clock format
24h
1
P02
Heating/Cooling Selection
Cooling
TPI for Underfloor Heating
TPI for Radiators
TPI for Electrical Heating
SPAN +/-0,1°C
TPI UFH
TPI RAD
TPI ELE
HIS 0.2
HIS 0.4
HIS 0.6
HIS 0.8
HIS 1.0
HIS 2.0
HIS 3.0
HIS 4.0
3
Name the device
and click„Done”
The thermostat has been
installed and displays the
main interface.
On the controller screen globe
icon appeared stating that
he has been he added to the
ZigBee network.
TPI UFH
for heating
HIS 1.0 for
cooling
SPAN +/-0,2°C
P03
Control algorithm
SPAN +/-0,3°C
SPAN +/-0,4°C
2
1
SPAN +/-0,5°C
2
SPAN +/-1,0°C
SPAN +/-1,5°C
In order to correctly link thermostat with the control box, first select the zone in the control box with the SELECT
button (1) (zone which you want to link with thermostat). The LED (2) will flash 3 times for the selected zone.
Confirm your selection by clicking PAIR button (2). The LED (2) will flash green with the previously selected
zone - binding process has started, it is active for 10 minutes and during this time you can link thermostat
with the selected zone.
SPAN +/-2,0°C
If the thermostat indicates wrong temperature, you can correct it by
max 3.5°C"
P04
Offset temperature
-3.5°C do +3.5°C
5°C - 45°C
0°C
Binding thermostat with the module/relay
P05
P06
"Minimum setpoint"
"Maximum setpoint"
Minimum heating / cooling temperature that can be set
5°C
Make sure that the module/relay and thermostat are in the same ZigBee network (they are added to the
same gateway).
5°C - 45°C
Maximum heating / cooling temperature that can be set
Disable
35°C
2
3
4
1
2
3
4
External sensor as a floor sensor
External sensor as an air sensor
Occupnacy sensor (ON/OFF volt free input)
2
P07
P08
S1/S2 Input
1
1
5x
Maximum floor temperature for heating
(function active when P07=2)
In order to protect the floor, the heating will be turned off, when the
temperature of the floor sensor rises above the maximum value.
5°C - 45°C
35°C
or
Minimum floor temperature for heating
(function active when P07=2)
In order to protect the floor, the heating will be switched on, when the
temperature of the floor sensor drops below the minimum value.
P09
P10
P11
5°C - 45°C
5°C - 45°C
5°C - 45°C
10°C
15°C
7°C
On the EONE thermostat,
hold and buttons until binding functionprocess of linking
the "bind"message appears. thermostat with control box is active.
Release the keys,
The "binding" process takes
up to 300 seconds.
Maximum floor temperature for cooling
(function active when P07=2)
In order to protect the floor, cooling will be switched on, when the
temperature of the floor sensor exceeds the maximum value.
5x
To properly link thermostat with the module/relay
first click quickly the button on the device 5 times.
The LED diode will start flashing slowly on red, which
means the device is in binding mode.
On the EONE thermostat, hold and buttons
until the "bind" message appears.
Minimum floor temperature for cooling
(function active when P07=2)
In order to protect the floor, cooling will be turned off, when the
temperature of the floor sensor drops below the minimum value
6
5
OFF
This function helps to keep the floor warm, even if there is no heating
demand from the room thermostat. This feature is available only for
Heating Mode. User can select 5 levels of warm floor feature. Note that
comfort warm floor function will activate heating for specified amount
of time (in relation to Level setting choosen by user). Heating will be
activated only if in the past 1 hour heating was OFF.
ATTENTION:
Level 1 = 7min
Level 2 = 11min
Level 3 = 15min
Level 4 = 19min
If the binding process fails, it
must be repeated taking into
account the distances between
devices, obstacles and local
radio signal interferences.
P12
Comfort warm floor
OFF
4
3
Level 5 = 23min
ON
OFF
Function disabled
Function enabled
3
P13
P14
P15
Valve protection
Backlight brightness
OFF
50%
NO
After successfull binding operation
„End”message will be displayed. successfully linked. Thermostat
displays the main screen, icon
Both devices have been
10% - 100%
Adjustable in the range from 10 to 100%
Remember:
NO
PIN
NO
Function disabled
Function enabled
Function disabled
Function enabled
No action
PIN Code for settings access
Radio range can be
increased by Engo
ZigBee repeaters.
Release the keys, binding function process of
linking thermostat with control box is active.
The "binding" process takes up to 300 seconds.
"
" appeared on the screen
indicating connection with the
receiver (ECB62ZB in this case).
Require a PIN to unlock the keys every time
(function active when P15=PIN)
P16
CLR
NO
NO
YES
NO
5
6
ATTENTION:
Clear settings factory reset
YES
Factory Reset
When the thermostat is binded with the module, the relay will turn off after 50 minutes,
if the communication between the devices is lost.
After successfull binding operation„End”
message will be displayed. LED on the module
will stop flashing.
Both devices have been successfully linked.
Thermostat displays the main screen, icon "
appeared on the screenindicating connection with
the receiver (module/relay in this case).
Installer settings
To enter installer parameters press and hold button for 3 seconds.
Factory reset
"
To RESET Thermostat to factory settings, hold down the and buttons until the FA message appears.
Then release the keys. Thermostat will restart, restore default factory settings and displays the home
screen. The device will be removed from the ZigBee network you will need to add/pair it again.
2
1
ATTENTION:
If the binding process fails, it must be repeated taking into account the distances between
devices, obstacles and local radio signal interferences.
SET
3 sec.
1
2
3
Remember:
Radio range can be increased by Engo ZigBee repeaters.
SET
ATTENTION:
Use or . button to move between parameters. Enter the parameter by . Edit the parameter using
or . Confirm the new parameter value with the button.
When the thermostat is binded with the module, the relay will turn off after 50 minutes,
if the communication between the devices is lost.
| General | Details |
|---|---|
| Name | ENGO CONTROLS EONE-BATW, EONE-BATB Internet Controlled Thermostat User Guide |
| Make | ENGO CONTROLS |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.53 MB |
(1 votes, average: 5.00 out of 5)
Loading...
ENGO Controls EONE230W Internet Controlled Thermostat User Guide
ENGO CONTROLS EFAN-230W Fan Coil Thermostat User Guide
ENGO CONTROLS FAN-24W 24V Fan Coil Thermostat User Guide
ENGO CONTROLS EASY230W Non-Programmable Wired Thermostat User Guide
ENGO CONTROLS EONE230 Internet Controlled Thermostat User Guide
ENGO CONTROLS EONEBATW, EONEBATB Internet Controlled Thermostat User Manual
ENGO Controls E901WIFI Internet Wireless Thermostat User Guide
ENGO CONTROLS EFAN-24W Fan Coil Thermostat User Guide
ENGO CONTROLS EFAN-230W WIFI 230V Fan Coil Thermostat User Guide
ENGO CONTROLS E10-MBUSW, E10-MBUSB Wi-Fi MODBUS Thermostat User Guide
Livn 147 Thermostat User Guide
DEVI 330 Electronic Thermostat Installation Guide
BOSCH BTH-RM Room Thermostat II User Manual
DEVIreg 316 Electronic Thermostat Installation Guide
ideal HEATING Halo Combi RF Wireless Boiler Thermostat User Guide
beok-controls TGM50 Smart WiFi Underfloor Thermostat User Guide
KeepRite TSTATIIEWF-01 Ion Gray Smart Thermostat Owner’s Manual
Tio 230v Thermostat User Manual
SALUS DT500 Thermostat User Guide
SIEMENS TH193 HC Heating-Cooling Room Thermostat Instruction Manual