ENGO CONTROLS ESIMPLE-230W 230V Simple Dial Thermostat Owner’s Manual

1

2

Introduction  

Package content  

Wiring diagrams  

SIMPLE  

ESIMPLE-230W / ESIMPLE-230B is a surface-mounted,  

wired room thermostat intended for surface heating /  

cooling, characterized by high thermal inertia. The room  

setpoint temperature is set with a knob. Thanks to the  

built-in algorithms, it offers much better temperature  

control accuracy than traditional mechanical thermostats.  

Simple Dial Thermostat 230V  

a) Connection diagram for pump/actuator  

Thermostat  

230V  

SL  

L

N

Thermostat  

white or black  

Cechy produktu  

max. 3(1)A  

ESIMPLE-230W  

ESIMPLE-230B  

simple thermostat with knob  

Quick Guide  

AC 230V  

TPI algorithm ideal for underfloor heating  

HEAT / COOL switch hidden under the knob  

two-color LED  

L

N

PE  

Ver. 5.1  

Release date: VII 2024  

Soft: v2.2  

Mounting screws  

Quick Guide  

b) Connection diagrams for the control box  

surface mounting  

Producer:  

Engo Controls sp z o.o. sp. k.  

4 Rolna St.  

Proper thermostat location  

Safety information:  

43-262 Kobielice  

Poland  

Thermostat  

230V  

Use in accordance with national and EU regulations. Use  

the device only as intended, keeping it in a dry condition.  

The product is for indoor use only. Please read the entire  

manual, before installation or use.  

SL  

L

N

N

L

Control box  

1 - 8 Zones  

SL..  

www.engocontrols.com  

Product Compliance  

This product complies with the following EU Directives:  

2014/30/EU, 2014/35/EU, 2011/65/EU.  

Technical informations  

Power supply  

Max load  

230V AC 50Hz  

3(1) A  

Installation  

Dimensions  

Installation must be performed by a qualified person with  

appropriate electrical qualifications, in accordance with  

the standards and regulations in force in a given country  

and in the EU. The manufacturer is not responsible for  

non-compliance with the instructions  

For the thermostat to work properly, it must be installed  

in a suitable place. Preferably approx. 150 cm above floor  

level, away from sources of heat or cold. In addition, the  

thermostat should not be installed behind curtains or  

other obstacles or in places with high humidity, as this will  

prevent an accurate measurement of the temperature in  

the room. It is not recommended to install the thermostat  

on an outside wall, in a draft or in a place where it will be  

exposed to direct sunlight.  

Temperatur control range  

5 – 30°C  

Control method  

Communication  

Output signal  

TPI or Hysteresis ( 0.5°C)  

Wired  

230V AC  

IP protection class  

Dimensions  

IP30  

WARNING:  

For the entire installation, there may be additional protection  

requirements, which the installer is responsible for.  

80 x 80 x 26 mm  

80 mm  

26 mm  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	ENGO CONTROLS ESIMPLE-230W 230V Simple Dial Thermostat Owner’s Manual
Make	ENGO CONTROLS
Language	English
Filetype	PDF (Download)
File size	0.14 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• ENGO CONTROLS

ENGO CONTROLS ESIMPLE-230W 230V Simple Dial Thermostat Owner’s Manual Overview

Summary of Contents

• Page 1: Introduction Package content Wiring diagrams ESIMPLE-230W / ESIMPLE-230B is a surface-mounted, wired room thermostat intended for surface heating/cooling, characterized by high thermal inertia. The room setpoint temperature is set with a knob. Thanks to the built-in algorithms, it offers much better temperature control accuracy than traditional mechanical thermostats. Use the device only as intended, keeping it in a dry condition. The product is for indoor use only. Please read the entire manual before installation or use. Installation must be performed by a qualified person with appropriate electrical qualifications. For the thermostat to work properly, it must be installed in a suitable place. Temperatur control range is 5 – 30°C. WARNING: For the entire installation, there may be additional protection requirements, which the installer is responsible for.
• Page 2: Wall mounting Switches for additional settings LED light indications The status of the thermostat is determined by the LED, illuminating in different colors. During wire connections procedure, please make sure they are not connected to the 230V AC power supply. Additional functions of the thermostats can be switched on or off by switches located on the front cover. A detailed explanation of the meaning of the LED lights can be found in the table below. The heating or cooling mode is based on the setting of the switches located under the knob on the front cover. The thermostat gives a possibility to choose the mode of controlling the room temperature by TPI algorithm or by hysteresis +/-0.5°C. The TPI algorithm is designed for underfloor heating to precisely maintain the room temperature.