DEVIreg 610 Electronic Thermostat Installation Guide

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

Installation Guide  

DEVIreg™ 610  

Electronic Thermostat  

www.DEVI.com  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	DEVIreg 610 Electronic Thermostat Installation Guide
Make	DEVI
Language	English
Filetype	PDF (Download)
File size	0.67 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• DEVI

DEVIreg 610 Electronic Thermostat Installation Guide Overview

Summary of Contents

• Page 1: Installation guide for DEVIreg™ 610 electronic thermostat.
• Page 2: DEVIreg™ 610 Installation guide
• Page 3: Introduction DEVIreg™ 610 is an electronic thermostat to be installed directly on the wall. It is provided with a 2-pole switch and a wire sensor to control the desired temperature. The thermostat has a button for adjusting the temperature setting with a scale from -10 °C to +50 °C, and an LED indicator that shows standby periods (green light) and heating periods (red light). Mounting Instructions Warranty Disposal Instruction
• Page 4: DEVIreg™ 610 Technical specifications Operating temperature range is -30°C to +50°C. Standby power consumption is a maximum of 0.93W. Relay specifications include a maximum of 10A / 2300W at 230V. Sensing units use NTC 15kOhm at 25°C. Sensing values at different temperatures are provided. Hysteresis is set at 0.2°C. The cable specification allows for a maximum of 1 x 4 mm² or 2 x 2.5 mm². The ball pressure temperature is rated at 75°C. The pollution degree is classified as 2 for domestic use. The storage temperature range is -20°C to +65°C.
• Page 5: DEVIreg™ 610 Dimensions: 100 x 69.5 x 45 mm Weight: 165 g The product complies with the EN/IEC Standard “Automatic electrical controls for household and similar use.” Safety Instructions: Make sure the mains supply to the thermostat is turned off before installation. The installation of the thermostat must be done by an authorized and qualified installer according to local regulations. The thermostat must be connected to a power supply via an all-pole disconnection switch. The sensor is to be considered as live voltage. Always connect the thermostat to continuous power supply. Do not expose the thermostat to moisture, water, dust, and excessive heat.
• Page 6: DEVIreg™ 610 Mounting instructions The thermostat can be placed both indoors and outdoors. Place the thermostat on a wall, pole, steel/wooden plate or pipe. In wet rooms, place the thermostat according to local regulation on IP classes.
• Page 7: DEVIreg™ 610 Follow the steps below to mount the thermostat. Open the thermostat: Set adjustment button to minimum temperature. Loosen the 2 screws and open the front cover. Installation Guide
• Page 8: Fasten the thermostat by driving screws through the holes in the bottom corners. Seal the holes with the enclosed screw stopper to maintain the density. Connect the thermostat according to the connection diagram. IP44 rating is specified. Operating temperature range is -10 to 50 degrees Celsius. Mains voltage is 220-240V. Maximum load is 10 (1) A. For heating, connect L-main, N-main, L-load, and NO (normally open) load. For cooling, connect L-main, N-main, L-load, and NC (normally closed) load. This is an installation guide.
• Page 9: The screen of the heating cable must be connected to the earth conductor of the power supply cable by using a separate connector. Ensure that the adjustment button can be adjusted within full temperature range, i.e. from -10 °C to +50 °C. Install sensor using the supplied sensor cable - spec. NTC 15 kΩ @ 25°C. Press out the blanket located at the bottom of the thermostat and insert the seal nipple. Connect sensor to terminals 6+7. The sensor cable can be extended up to 50 m with 1,5 mm² installation cable without affecting the accuracy of the thermostat. Do not place the cable parallel to other installation cables as undesirable signals may be induced. The installation must be permanent. If the sensor is to be built in, used for pipe applications, or exposed to pressure, always install it in a conduit. Turn on the power supply.
• Page 10: Warranty A 2-year product warranty is valid for DEVIreg™ 610 thermostats. Danfoss offers a warranty valid from the date of purchase under specific conditions. During the warranty period, Danfoss may provide a new comparable product or repair the faulty product. The decision to repair or replace is at the discretion of Danfoss. Danfoss is not liable for consequential or incidental damages. The warranty is valid only if the warranty certificate is completed correctly. The warranty certificate must be filled in, stamped, and signed by the authorized installer. Danfoss warranty does not cover damage from incorrect use or installation by non-authorized electricians. All work will be invoiced if Danfoss inspects or repairs faults due to incorrect conditions. The warranty explicitly excludes all claims exceeding the stated conditions.
• Page 11: Warranty certificate details include the name of the warranty holder, address, purchase date, serial number of the product, product information, and installation and connection dates with signatures.
• Page 12: DEVIreg™ 610 Installation guide
• Page 13: Disposal instruction Installation guide
• Page 14: DEVIreg™ 610 Installation guide
• Page 15: Page 15
• Page 16: DEVIreg™ 610 Product documentation Designed in Denmark for Danfoss A/S IP 44 10 A / 2300 W @ 230 V~ -10 to +50 °C 220-240 V~ 50-60 Hz~ For UK customer only: Importer: Danfoss Ltd.