DAIKIN IM 1366 Remote Integrated Thermostat Instruction Manual
Table 2: Thermostat Display Icons
Initial Start-up and Display
Descriptions
Number
Function
1
Temperature Area, showing room temperature
and set point in C or F. The temperature unit
can be selected in service mode of room unit if
relevant option was created by the controller.
Initial Start-up
It may take up to 5 minutes on initial power up for the
integrated thermostat to establish communications with the
MicroTech 4 Lite controller.
2
3
Time
Fan Speed
4
Weekday indicator
On / Off
5
Display descriptions and Button
Operation
6
Auto mode active
Economy mode active
Comfort mode active
Cooling
7
Thermostat Status Cycle
8
Area 1 shown in Figure 4 will cycle through displaying the
current measured room sensor temperature and the active
setpoint. Each status will display for approximately 5 seconds
before switching to the other.
9
10
11
12
13
14
15
16
17
Heating
Dehumidification
Fan only
• Room sensor temperature along with the thermometer
icon in Area 1. Current time in Area 2.
N/A
• Active setpoint in Area 1 without the thermometer along
with the corresponding cooling or heating icon. Displays
“STPT” in Area 2.
Occupancy mode
N/A
Alarm indicator
Service mode
Figure 4: Thermostat Display
Adjusting the setpoint
Temporary Setpoint adjustment is performed by pressing the
minus (-) and plus (+) buttons and Effective Occupancy must
also be set to OCCUPIED or BYPASS.
NOTE: Temporary Setpoint adjustment will not function if the
thermostat is in the Program Mode or if the Effective
Occupancy is set to STANDBY or UNOCCUPIED.
Pressing the minus (-) or plus (+) buttons will make Area
1 display the current active setpoint value along with the
corresponding cooling or heating icon. Area 2 will change from
displaying the time to "STPT".
Subsequent presses of the minus (-) or plus (+) buttons will
adjust the setpoint value up or down and will increment by 0.5
degrees.
Pressing the OK button after changing the setpoint value will
confirm the setpoint change.
• If the OK button is not pressed within 10 seconds of the
last press of the minus (-) or plus (+) buttons, the change
will be discarded and the display will exit the setpoint
adjustment state.
Pressing the OK button will then switch the display to the other
setpoint value along with the corresponding heating or cooling
icon, and allow the user to adjust this setpoint.
IM 1366
4
| General | Details |
|---|---|
| Name | DAIKIN IM 1366 Remote Integrated Thermostat Instruction Manual |
| Make | Daikin |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.28 MB |
(1 votes, average: 5.00 out of 5)
Loading...
DAIKIN One Lite Smart Thermostat User Guide
Daikin One Lite Smart Thermostat Instruction Manual
DAIKIN TRC-11 One Lite Connected Thermostat Instruction Manual
DAIKIN DTST-ONE-ADA-A One Touch Smart Thermostat Installation Guide
DAIKIN IM 1368 Vertical Stack WSHP Thermostat Instruction Manual
DAIKIN ONE Smart Thermostat Instructions
DAIKIN DKN509 Wireless Communicating Thermostat Instruction Manual
DAIKIN SQNSQ22 One Touch Smart Thermostat User Manual
EMSQ22 Daikin ONE Lite Smart Thermostat User Manual
DAIKIN S21 One Lite Smart Thermostat User Guide
GENERAL LIFE SOLARA 330S Digital Room Thermostat User Manual
Daikin One Lite Smart Thermostat Instruction Manual
honeywell RLV3150 Electronic Thermostat User Manual
vtech T961NN50 Wired Thermostat User Guide
SHANGHAI TR9B Ultra Large Colorful Screen Capacitive Touch LCD Smart Thermostat User Guide
BEOK TDS23 Wifi Thermostat Owner’s Manual
Danfoss RET230 HCW-1 Electronic Heat Cool Thermostat User Manual
Honeywell T8775 Digital Round Thermostat Instructions
Innova B3V151 Electronic Thermostat User Manual
GENERAL LIFE ARUNA 302S RF Digital Room Thermostat User Manual