SKYTECH 5320P Programmable Thermostat Fireplace Remote Control Instruction Manual
SETTING THE TEMPERATURE SWING (TEMPERATURE DIFFERENTIAL)
The Thermo Mode on the transmitter operates the appliance whenever the room
temperature varies a certain number of degrees from the set temperature. This
variation is called the “SWING” or TEMPERATURE DIFFERENTIAL. The factory
preset swing temperature is 2º F (1º C). To change the “Swing Setting:”
•
Press the SET button and the DOWN touch button simultaneously to display the
current “swing” setting in the set temp frame. The letter “S” will display in the
room temp frame on the LCD screen.
•
•
Press the UP or DOWN touch button to adjust the “SWING” temperature (1º- 3º F)
(1º- 2º C).
To store the “swing” setting press the SET button, and the new “swing” setting will
be automatically programmed.
Fig. 19 Swing setting.
TRANSMITTER WALL MOUNT BRACKET
The transmitter can be placed on a wall using the mount provided.
•
•
Wood - Drill 1/8’’ pilot holes and install with screws provided.
Plaster/Wallboard - Drill 1/4’’ holes, use a hammer to tap in the two plastic
anchors. Then install with the screws provided.
Fig. 20 Wall plate mounting.
WARNING
This remote control system must be installed exactly as outlined in these instructions. Read all instructions completely
beore attempting installation. Follow instructions careully during installation. Any modications o this remote control
or any o its components will void the warranty and may pose a re hazard.
Consult gas appliance manufacturer’s instructions and wiring schematics for proper placement of all wires. All electronic
modules are to be wired to manuacturer’s specications.
The following wiring diagrams are for illustration purpose only. Follow instructions from manufacturer of gas valve and/
or electronic module for correct wiring procedures. Improper installation of electric components can cause damage to
electronic module, gas valve and remote receiver.
RECEIVER
When plugged into a standard 110-120 VAC receptacle, the remote receiver
operates on commands from the transmitter or from the slide switch on the face
of the receiver (This switch is to be used during a power outage to operate the
appliance manually).
•
•
ON: will manually turn ON the appliance.
REMOTE: will allow use of handheld transmitter. If the system does not
respond to the transmitter on initial use, ensure it is plugged into a 110-
120VAC receptacle . If that does not work, see the LEARNING TRANSMIT-
TER TO RECEIVER section.
LEARN
•
•
OFF: will disable the remote receiver.
Place the slide switch in the OFF position if you will be away from
your home for an extended period of time.
The remote receiver is manufactured with a “dry contact” relay in its circuitry
that operates like an ON/OFF switch. However, no power or current passes
from the 110-120VAC input side to the wires leading from the output side of the
remote receiver.
Fig. 21 Electric receiver.
REV. 8-11-20 Page 6
Skytech: 5320P
| General | Details |
|---|---|
| Name | SKYTECH 5320P Programmable Thermostat Fireplace Remote Control Instruction Manual |
| Make | Skytech |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.49 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Honeywell TH6320ZW T6 Pro Z-Wave Programmable Thermostat User Guide
EPH CDTP2 Room Thermostat Installation Guide
Honeywell TH8732WFH5004 Round Smart Thermostat User Guide
EXPERT4HOUSE BAC-9000 Smart Knob Thermostat User Guide
Honeywell FocusPRO TH5000 Series Non-Programmable Digital Thermostat Instruction Manual
AFRISO RT 10 D 230 Room Thermostat Instruction Manual
Price Industries Disio Display Thermostat User Guide
Danfoss GreenCon RC-T2/T4 Room Thermostat Installation Guide
aube technologies TH110A-DP-P Thermostat User Manual
ESi ESRTP4RFW Programmable Room Thermostat Installation Guide