Home > Skytech > SKYTECH 5320P Programmable Thermostat Fireplace Remote Control Instruction Manual

SKYTECH 5320P Programmable Thermostat Fireplace Remote Control Instruction Manual

LEARNING TRANSMITTER TO RECEIVER  
Each transmitter uses a unique security code. It will be necessary to press the LEARN button on the receiver to accept  
the transmitter security code upon initial use or if a replacement transmitter is purchased from your dealer or the factory.  
In order for the receiver to accept the transmitter security code, be sure the slide button on the receiver is in the REMOTE  
position; the receiver will not LEARN if the slide switch is in the ON or OFF position. The LEARN button in located on  
the front face of the receiver; inside the small hole labeled LEARN. Press and Release the black LEARN button inside  
the hole. When you release the LEARN button the receiver will emit an audible “beep”. After the receiver emits the beep  
press the transmitter MODE button and release. The receiver will emit several beeps indicating that the transmitter’s code  
has been accepted into the receiver.  
OFF  
REMOTE  
ON  
LEARN  
Fig. 24 Receiver slide switch.  
Fig. 25 Learn button.  
THERMO SAFETY FEATURE  
If the receiver at anytime should reach 130ºF, the receiver will automatically shut down and begin to beep 3 beeps every 2  
seconds. Once the temperature has dropped between 120ºF and 130ºF, the user can reactivate the appliance by  
pressing the MODE button, but the beeping will continue until temperatures drop below 120ºF. This is to tell the user that  
the receiver needs to be relocated to reduce temperatures.  
If this situation happens, the receiver should be placed somewhere else where it will not reach temperatures in excess of  
130ºF.  
BATTERY LIFE  
Life expectancy of the alkaline batteries in the transmitter should be at least 12 months. Check and replace all batteries:  
•
•
•
•
Annually.  
When operating range becomes reduced.  
When transmissions are not received by the remote receiver.  
If the hand held transmitter batteries measure less than 5.3 volts all (4) batteries in combination).  
TROUBLE SHOOTING  
Iyou encounter problems with your replace system, the problem may be with either the replace itselor with the re-  
mote. Review the replace manuacturer’s operation manual to make sure all connections are properly made, then check  
the operation of the remote in the following manner:  
•
Make sure all batteries are correctly installed in the transmitter and receiver. Also check that the batteries are fully  
charged.  
•
Check batteries in transmitter to ensure contacts are touching (+) and (-) ends of battery. Bend metal contacts in for  
tighter t.  
•
•
•
Be sure receiver and transmitter are within 20 to 25-foot operating range.  
Keep receiver from temperatures exceeding 130º F.  
If no beeps are heard from the receiver clear codes by pressing and holding the learn button for 10 seconds, then  
release.  
•
•
•
•
Check to ensure the pilot knob (on gas valve) is in the ON position.  
If receicver is beeping, refer to page 5 for COMMUNICATION SAFETY.  
If receiver is installed in a tightly enclosed metal surrounding, the operating distance will be shortened.  
Make sure the hand-held transmitter and remote receiver are communicating properly (see LEARNING  
TRANSMITTER TO RECEIVER on page 8).  
REV. 8-11-20 Page 8  
Skytech: 5320P  
GeneralDetails
NameSKYTECH 5320P Programmable Thermostat Fireplace Remote Control Instruction Manual
MakeSkytech
LanguageEnglish
FiletypePDF (Download)
File size0.49 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...

SKYTECH 5320P Programmable Thermostat Fireplace Remote Control Instruction Manual