Home > Robertshaw > Robertshaw RS9320T Programmable Touchscreen Wall Thermostat Instruction Manual
Robertshaw RS9320T Programmable Touchscreen Wall Thermostat Instruction Manual
Installer Setup Menu
Installer Setup Menu
1. Press MENU.
Settings
Display
Adjustment Options
Default
2. Press and hold TECHNICIAN SETUP for 3 seconds.
3. Configure the installer options as desired using the table below.
The heating differential is factory
preset at 0.4°. This means that
whenever the room temperature
cools by 0.4° from the temperature
setting, the heating system will
turn on. If the heating system
turns on too often, increase the
temperature differential.
4. Use
or
from one step to another. Note: Only press DONE when you want to exit the
to change settings and NEW STEP or PREV STEP to move
Installer Setup options.
Heating
Differential
The heating differential setting is
adjustable from 0.2°F to 2°F.
0.4
Settings
Display
Adjustment Options
Default
This setting will flash FILT in the
display after the elapsed run time
to remind the user to change the
filter. The OFF setting will disable
this feature.
The filter change reminder can
be adjusted from OFF to 2000
hours in 50 hour increments.
Filter Change
Reminder
OFF
Use
or
to configure the
The thermostat can be optionally
configured to operate a heat pump.
setting. OFF for conventional
systems and ON for heat pump
systems.
Heat Pump
0FF
0FF
This setting allows the installer to
change the calibration of the room
temperature display so that, for
example, the thermostat would read
72°F instead of 70°F.
The room temperature display
can be adjusted to read 3° above
or below the factory calibrated
temperature.
Room
Temperature
Calibration
0
The system switch can be
configured for the particular
application. Heat-Off-Cool, Heat-Off,
Cool-Off, Heat-Off- Cool-Auto.
The minimum compressor run
time can be adjusted from OFF
to 3, 4, or 5 minutes. If 3, 4, or 5
is selected, the compressor will
run for at least the selected time
before turning off (although the
fan may continue to run for a
short time).
Use
desired application is flashing.
AUTO = (Auto Changeover)
or
until the
System
Switch
The installer can select the minimum
run time for the compressor to help
protect the compressor from short-
cycling.
Minimum
Compressor
On-Time
Note: Emergency Heat is available
in heat pump mode only.
OFF
ON
0.5
Use
or
to select stages
If the heat pump is still ON, this
thermostat can be configured to
operate up to 2H/2C conventional,
or up to 4H/2C heat pump system.
Stages of
Heat and
Cool
of heat, press NEXT, then select
stages of cool. 3 or 4 heat will
use Y1 and Y2 as 1st and 2nd
stage of heat.
The compressor short cycle delay
setting will not allow the compressor
to be turned on for 5 minutes after it
was last turned off in order to protect
the compressor.
Compressor
Short Cycle
Delay
The compressor short cycle
delay setting can be removed
by selecting OFF.
2
STAGES
The cooling differential is factory
preset at 0.5°. This means that
whenever the room temperature
heats by 0.5° full degree from the
temperature setting, the cooling
system will turn on. If the cooling
system turns on too often, increase
the temperature differential.
The cooling fan delay can be set
to OFF, 15, 30, 60 or 90 seconds.
If 15, 30, 60 or 90 is selected, the
fan will not turn on for at least
the selected time when there
is a call for cool and will run for
at least the selected time after
satisfying the call for cool.
The cooling fan delay setting delays
the fan from coming on in cool
mode and keeps it running after
the compressor shuts off for a short
time in order to save energy.
Cooling
Differential
Cooling Fan
Delay
The cooling differential setting is
adjustable from 0.2°F to 2°F.
0FF
9
10
Installer Setup Menu
Installer Setup Menu
Settings
Display
Adjustment Options
Default
Settings
Display
Adjustment Options
Default
This thermostat can be configured to
have 7 Day, 5+1+1 programming or
be non-programmable.
This setting establishes a
maximum value above which
the set-point temperature value
cannot be raised.
Use
or
to
Heating
Temperature
Set-Point
Limit
select the maximum heat
temperature set-point.
90°
If 7 Day is selected, in Set Time
all seven days will need to be
programmed individually.
Range 44°F - 90°F
Use
7 day, 5d for 5+1+1, or Od for
non-programmable.
or
to select 7d for
Program
Options
If 5+1+1 programming is selected,
in Set Time Monday–Friday will
be programmed together and
Saturday and Sunday will need to be
programmed individually.
5d
This setting establishes a
maximum value above which
the set-point temperature value
cannot be lowered.
Use
or
to
Cooling
Temperature
Set-Point
Limit
select the minimum cool
temperature set-point.
44°
F°
Range 44°F - 90°F
If 0d is selected, the thermostat
becomes non-programmable.
Select F for Fahrenheit temperature
display or select C for Celsius
display.
F OR C SET
°F for Fahrenheit
°C for Celsius
F° or C°
The display light can be configured to
come on when any key is pressed or to
stay on all of the time.
AUTO - Any key ON
Display
Light
AUTO
ON - Always ON
12 or 24
12 Hour
Clock
Use
12 or 24 hour clock.
or
to select
Select a 12 or 24 hour clock setting.
Hour Clock
If selected ON, the input screen
will appear after pressing Next
Contractor
Call
Number
The thermostat allows installers to put
their phone number in the display.
Step. Use
or
to select
Fan
Operation
Select GAS or ELEC depending
on the type of furnace.
GAS or ELEC
OFF
the desired telephone number
and the FAN or SYSTEM key to
change characters.
GAS
ON
This setting will start heating early
to bring the building temperature
to its programmed set-point by
the beginning of the WAKE time
period.
If ON is selected,
the beep will sound.
Morning
Recovery
The thermostat can be configured to
make an audible beep when any key
is pressed.
Use
or
to turn on or off.
Beep
ON
If OFF is selected,
the beep will be silenced.
11
12
| General | Details |
|---|---|
| Name | Robertshaw RS9320T Programmable Touchscreen Wall Thermostat Instruction Manual |
| Make | Robertshaw |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.84 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Robertshaw RS9220 Programmable Thermostat Installation Guide
Robertshaw RS10420T WIFI Programmable Thermostat User Guide
Robertshaw RS8110 Non Programmable Thermostat Instruction Manual
Robertshaw RS8210 Thermostat Installation Guide
Robertshaw RS8210 Non-Programmable Multi-Stage 2H-1C Wall Thermostat User Manual
Robertshaw RS9220 Digital Programmable Wall Thermostat Instruction Manual
Robertshaw 9602 Programmable Thermostat User Manual
Robertshaw RS9423T Thermostat Installation Guide
Robertshaw RTC500 WIFI Thermostat Instruction Manual
Robertshaw RS1110 Programmable 1 Heat 1 Cool Wall Thermostat Instruction Manual
OSCAR OS20 LCD Thermostat Instruction Manual
eurotronic Comet Zigbee Energy Saving Radiator Thermostat Instruction Manual
GENERAL LIFE Mitra 230S RF Wireless Room Thermostat User Manual
sinope TH1134ZB Smart Line Voltage Thermostat Installation Guide
HITACHI ATW-RTU-12 Room Thermostat Instruction Manual
DEVIreg 610 Electronic Thermostat Installation Guide
Puravent CFST Frost Thermostat Installation Guide
Beok Controls TS4 Series Thermostat User Guide
DeLOCK Thermostat for DIN Rail User Manual
olympia electronics BS-850-KIT Wireless Programmable WiFi Electronic Chrono Thermostat User Manual