Home > NEOMITIS > NEOMITIS RTE0RFA Wireless Digital Room Thermostat and Receiver Instruction Manual

NEOMITIS RTE0RFA Wireless Digital Room Thermostat and Receiver Instruction Manual

5- Secure the thermostat by screwing the  
locking screws under the thermostat.  
INSTALLATION - THERMOSTAT  
x2  
Recommended locaꢀons  
for your thermostat.  
To ensure that your  
thermostat provides  
accurate readings and  
controls effecꢁvely, it must  
be installed approximately  
1.5 m above floor level on  
an inside wall, away from  
direct sunshine and any other  
sources of heat or cold such  
as radiators, cold draughts,  
etc.  
• On the table stand  
1- Insert the 2 pins inside the wallplate.  
2- Slide the stand to the right.  
NB: In order to ensure proper operaꢁon of the product, ensure that the thermostat is  
not posiꢁoned near to an area which could be affected by interference from another  
source. E.g.: a wireless transmiꢀer or receiver, TV, PC, etc.  
Important: The thermostat measures the temperature of the place where it is installed.  
It does not take into account the temperature differences that may exist between diffe-  
rent locaꢁons in the house if the temperature is not uniform.  
INSTALLING BATTERIES  
1- Remove the baꢀeries  
cover which is placed on  
the front of thermostat.  
2- Insert the 2 baꢀeries AA 3- Replace the baꢀeries  
supplied. Note the cor-  
rect polarity according  
to the engraving on the  
thermostat when inser-  
ꢁng the baꢀeries.  
cover.  
3- Fold the stand and lock it into the  
wallplate.  
4- Tilt the thermostat according to its  
placement in the room. 2 ꢁlts are  
available.  
30°  
37°  
MOUNTING OF THERMOSTAT  
• On the wall  
1- Unscrew the 2 screws under the  
2- Remove the wall plate from the  
thermostat.  
thermostat.  
PAIRING PROCEDURE  
The thermostat and the receiver are not bonded together at the factory.  
To bond the transmiꢀer and the receiver together, proceed as below:  
x2  
1- Press and hold for 5 seconds the RF  
test buꢀon on the receiver. RF test  
green light is blinking.  
2- Within 1 minute, press and hold for  
5 seconds the RF test buꢀon on the  
thermostat. Pairing icon is flashing.  
3- Secure the wall plate with the two  
screws provided using the horizontal  
and verꢁcal holes.  
4- Replace the thermostat on the wall  
mounꢁng plate.  
Override  
RF Test  
Override  
RF Test  
5 sec  
5 sec  
2
GeneralDetails
NameNEOMITIS RTE0RFA Wireless Digital Room Thermostat and Receiver Instruction Manual
MakeNEOMITIS
LanguageEnglish
FiletypePDF (Download)
File size1.58 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...
NEOMITIS RTE7OTA Wired Digital 7 Day Programmable Smart Room Thermostat Instruction Manual
NEOMITIS RTE7OTA Wired Digital 7 Day Programmable Smart Room Thermostat Instruction Manual
Neomitis RTMA Mechanical Room Thermostat Instruction Manual
Neomitis RTMA Mechanical Room Thermostat Instruction Manual
NEOMITIS RTE7D, RTE7BD Wired Digital 7 Day Programmable Room Thermostat Instruction Manual
NEOMITIS RTE7D, RTE7BD Wired Digital 7 Day Programmable Room Thermostat Instruction Manual
NEOMITIS Rtaneoa Wired Analog Room Thermostat Instruction Manual
NEOMITIS Rtaneoa Wired Analog Room Thermostat Instruction Manual
NEOMITIS PRG7 RF 7 Day Two Channel Programmer with RF Room Thermostat Instruction Manual
NEOMITIS PRG7 RF 7 Day Two Channel Programmer with RF Room Thermostat Instruction Manual
NEOMITIS RTE7SD Mains Powered Digital 7 Day Programmable Room Thermostat Instruction Manual
NEOMITIS RTE7SD Mains Powered Digital 7 Day Programmable Room Thermostat Instruction Manual
NEOMITIS RTE0B Wired Digital Room Thermostat Installation Guide
NEOMITIS RTE0B Wired Digital Room Thermostat Installation Guide
NEOMITIS RTUa Mechanical Room Thermostat Instruction Manual
NEOMITIS RTUa Mechanical Room Thermostat Instruction Manual

NEOMITIS RTE0RFA Wireless Digital Room Thermostat and Receiver Instruction Manual