Honeywell TH6320ZW2003 Pro Z-Wave Programmable Thermostat Installation Guide
Read and save these instructions.
Introduction
The T6 Pro Z-Wave Programmable Thermostat is a Z-Wave Plus certified thermostat
capable of controlling up to three heat and two cool stages of heat pump, (incl. dual
fuel heat pump systems) and up to two heat and two cool stages of conventional
system (3H/2C HP, 2H/2C Conv.) It also measures, displays and reports % indoor
relative humidity; however, this model does not control humidification equipment.
It is one of the easiest smart thermostats to install and is controllable by all Z-Wave
compliant controllers that have the control capability for "Thermostat" devices.
When integrated with the app that controls your Z-Wave controller, it lets you pro-
gram and control your home’s HVAC system as well as controlling other Z-Wave
devices connected to the same Z-Wave controller.
The T6 Z-Wave thermostat has Dynamic Capabilities configuration settings which
can be adjusted from a Dynamic Capabilities enabled controller in the network.
Parameters that can be adjusted:
• Thermostat Mode
• Fan Mode
• Set Point Mode
If the ISU settings for system type or cooling stages are changed on device or
through a Z-Wave controller, the available settings may change. See "(ISU) Advanced
menu" section in this guide.
NOTE: Some controllers will require the thermostat to be rediscovered or removed
and then included again in order for configuration changes to be reflected.
Because the thermostat is battery-powered, low-voltage integrators
can easily connect the thermostat to most HVAC systems. Optional
24 VAC powering via “C” or common wire is also available, if desired.
CAUTION
•
We strongly recommend that installation is performed by a trained HVAC
technician.
•
Read the enclosed instructions carefully before installing the new T6 Pro Z-Wave
Programmable Thermostat.
•
ELECTRICAL HAZARD: Can cause electrical shock or equipment damage.
Disconnect power before beginning installation.
•
To prevent abnormal operation, it is highly recommended to configure the
installer setup and set the thermostat to correct HVAC system before including the
thermostat to Z-Wave network. If the configuration must be changed, first REMOVE
the thermostat from the network, change the thermostat configuration, and
INCLUDE the thermostat back to the network.
•
Before disconnecting wires from the existing thermostat, label the wires with the
terminal markings from the old thermostat and record them. Take a picture of the old
wiring.
•
Use 3 new AA batteries in the thermostat.
2
| General | Details |
|---|---|
| Name | Honeywell TH6320ZW2003 Pro Z-Wave Programmable Thermostat Installation Guide |
| Make | Honeywell |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.34 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Honeywell T6 Pro Programmable Thermostat User Manual
Honeywell D1-528 Direct Thermostat Installation Guide
Honeywell FocusPRO P200 Programmable Thermostat User Guide
Honeywell RCHT8610WF Series Smart Thermostat Installation Guide
Honeywell T9 Smart Thermostat Installation Guide
Honeywell TH2320WF4011 FocusPRO Smart S200 Series Thermostat User Guide
Honeywell TL116A Thermostat Installation Guide
T10 Pro Smart Thermostat with Redlink Room Sensor
Honeywell TH6320WF2003 Lyric T6 Pro Wi-Fi Programmable Thermostat User Guide
Honeywell RTH9580 Wi-Fi Color Touchscreen Programmable Thermostat User Guide
UNDERFLOOR HEATING WORLD UM1 Thermostat Instruction Manual
Danfoss RTD 014G0251 Ally Radiator Thermostat User Guide
WATTS TEK564 Invita WiFi Thermostat Instruction Manual
ideal HEATING Halo Lite RF Combi Wi-Fi Wireless Boiler Thermostat Instructions
EMOS P5611OT Wireless Thermostat Instruction Manual
VEVOR ET-72G Programmable Thermostat Instruction Manual
STELPRO STE302NP Programming Electronic Thermostat
CENTER EHE0200123 Wired 7 Day Programmable Thermostat Installation Guide
VIESSMANN ViCare ZK05991 Wireless Thermostat Instruction Manual
tado TRV3 Smart Radiator Thermostat User Guide