Warmme ET-72G(W) Thermostat User Manual

1

2

Event default parameter list  

Home  

Tap OK to confirm.  

Tap OK to return to the real-time temperature interface.  

Step 3: Click ‘Add Device’ or ‘+’ on the top-right to add device.  

Return  

Sleep  

Week  

Wake  

Leave  

8.Readout  

Tempera-  

ture  

Tempera-  

ture  

Tempera-  

ture  

Tempera-  

ture  

This thermostat has the function of calculating the percentage of heating time over a period of time.  

The relevant parameters can be queried through the Readout item.  

Readout query method:  

After entering Settings, tap ▲ or ▼ to select Readout.  

Tap OK to enter the selection.  

Start time  

Start time  

Start time  

Start time  

Step 4: Click ‘WiFi thermostat’.  

Mon--Fri  

6:00  

8:00  

78°F  

78°F  

8:00  

8:30  

69°F  

79°F  

17:00  

17:30  

78°F  

78°F  

22:00  

22:00  

69°F  

69°F  

Sat--Sun  

Office  

Step 5: Operate thermostat. If the WIFI icon flash quickly,  

User  

Click ‘Press to connect’.  

Tap ▲ or ▼ to select 1Day, 30Days or 365Days to query.  

Tap OK to return to the setting item selection.  

Week  

on-work  

off-work  

Step 6:  

Enter Wifi password, and click ‘Confirm’.  

Tempera-  

ture  

9.Factory reset  

Tempera-  

ture  

manual  

Start time  

Start time  

This thermostat has the function of restoring factory parameters.  

Mon--Fri  

Sat--Sun  

7:00  

7:00  

78°F  

68°F  

18:00  

18:00  

69°F  

69°F  

Factory Reset setting method:  

After entering Settings, tap ▲ or ▼ to select Factory Reset.  

Tap OK to enter the selection.  

Tap ▲ or ▼ to select Yes or No.  

Tap OK to confirm.  

Step 7: If device added successfully, you can change the device name and set region,  

then, click ‘Done’.  

Attention: If failed, please confirm the Wifi is 2.4G version and check the Wifi  

signals, then, use the ‘AP mode’ in the top right to connect again.  

Settings  

In addition to the above common functions, the thermostat also provides a number of settings for  

more occasions. It should be noted that such settings need to be set by professional technicians  

to avoid damage caused by abnormal settings.  

Tap OK to return to the real-time temperature interface.  

Step 8: You can check the real-time temperature and set temperature etc. at the control  

Settings access method:  

Settings default parameter list  

interface.  

Under real-time temperature interface, tap OK to enter the first level menu, and Mode is flashing.  

Tap ▲ or ▼ to select Settings.  

Tap OK to enter Settings.  

NO.  

1

Name  

Time  

Default Parameter  

/

Setting Range  

/

°F  

°C  

Settings contains the following items:  

2

°F/°C  

°F  

1.Time  

00 3950  

01 3600  

02 3700  

Set the current real time and day of the week.  

Note: The WiFi version of the thermostat will automatically update to local time after networking.  

Time setting method:  

3

Sensor Type  

00 3950  

Functions and operation  

On/Off  

Room  

The GFCI Reset button is also the switch button. Press the [Reset] button to switch on and off.  

After entering Settings, tap ▲ or ▼ to select Time.  

Tap OK to enter the hour setting for the time.  

Tap ▲ or ▼ to select the hour value for the current time.  

Tap OK to enter the minute setting for the time.  

Tap ▲ or ▼ to select the minute value for the current time.  

Tap OK to enter the day of the week setting.  

Tap ▲ or ▼ to select the day of the week.  

4

Sensor Selection  

Floor  

FLoor  

Room.Limit  

Temporary Override Temperature  

5

6

Calibration  

Location  

0°F  

-9°F -- 9°F  

This function is enabled in the automatic intelligent mode, when the temperature demand changes  

at this moment, the setting temperature is enabled, but the parameters in the Event are not  

changed.  

Home  

Office  

Home  

Yes  

No  

Operation method:  

7

Adaptive  

No  

Under the interface showing the real-time temperature, tap ▲ or ▼ to modify the set temperature.  

Tap OK to confirm and return to the interface showing the real-time temperature.  

Tap OK to enter the hour setting for the time.  

8

9

Readout  

/

/

Tap  

multi times to return to the real-time temperature interface.  

Yes  

No  

Factory Reset  

No  

Mode selection  

2. Temp unit  

°F or °C can be selected as the temperature unit.  

Temp Unit setting method:  

After entering Settings, tap ▲ or ▼ to select °F/°C.  

Tap OK to enter the selection.  

Tap ▲ or ▼ to select the desired temperature unit.  

Tap OK to confirm.  

Tap OK to return to the real-time temperature interface.  

This thermostat provides three operating modes:  

Automatic mode: According to the weekly program, the thermostat automatically adjusts the set  

temperature operation.  

Manual mode: The thermostat runs continuously according to the set temperature.  

Frost protection mode: The temperature controller runs at a lower set temperature. The temperature  

range is set from 41°F to 59°F in this mode. This mode is used when you want to keep your room at a  

lower temperature when you are on vacation.  

Troubleshooting  

E1: Built-in probe failure, please contact your dealer or professional technician.  

E2: External probe failure, please contact your dealer or professional technicia  

Installation  

How to set the mode selection:  

In the interface displaying the real-time temperature, tap OK to enter the first level menu, and  

Mode is flashing.  

Tap OK to enter the mode selection.  

Tap ▲ or ▼ to change the mode.  

Tap OK to confirm your selection.  

If you select manual mode or freeze protection mode, you also need to tap ▲ or ▼ to set the  

temperature.  

1.Loosen the bottom screw by a Phillips screwdriver. Then  

open the thermostat from the upper right side as shown.  

Note: Screw the nut out of the groove and do not need to  

unscrew it.  

3.Sensor type  

This thermostat can be connected not only to the floor sensor but also to two other  

commonly used floor sensors. When replacing the old thermostat, there is no need to replace the  

floor sensor for easy installation.  

Sensor Type setting method:  

After entering Settings, tap ▲ or ▼ to select Sensor Type.  

Tap OK to enter the selection.  

Tap ▲ or ▼ to select the type of floor sensor you are currently using.  

Tap OK to confirm.  

Tap OK to return to the real-time temperature interface.  

ET-72G(W) English V1.2  

2. Wire as shown:  

L/N lead: Connect the power cord using the terminal block.  

L1/N1 lead: Use a terminal block to connect the load line.  

IN/SNR terminal:Connect the floor sensor.  

OUT terminal:Connect to IN/SNR of Power Module.  

Tap OK to return to the interface showing the real-time temperature.  

Instruction  

Key lock  

Note: Disconnect the main power supply before wiring.  

If an electric floor heating cable or mat system requires more than 15 Amps, install a power module.  

Wiring diameter: 12 to 22 AWG.  

3. Install the back  

cover into the  

The ET-72G series thermostats control the floor heating system based on built-in weekly program. The  

weekly program runs in 4 or 2 stages per day, 7 days a week. The default weekly program parameters  

can satisfy most usage scenarios. If your living habits are different, you can also modify the weekly  

program parameters in the thermostat or APP. When there is no one in the house, it is recommended to  

set the temperature down to save energy. Besides, the thermostat has built-in adaptive function. When  

this function acts, the thermostat heats or stops heating in advance of next stage to bring the room  

temperature to the set temperature of the next stage. Please note that after turning adaptive on, the  

thermostat takes a few days to learn the time required.  

The thermostat provides a key lock function to prevent the thermostat setting parameters from  

being incorrectly modified.  

Note: the [Reset] button and the [Test Monthly] button can still operate normally so as to response  

to an emergency.  

No.  

00  

Sensor Type  

3950(default)  

3600  

Parameters  

terminal box and  

secure it with  

the set screw.  

Set the key lock mode:  

1. Under real-time temperature interface, press and hold  

2. Under real-time temperature interface, tap OK to enter the first level menu, and Mode is  

01  

02  

R(25°C)=12kΩ R(10°C)=22.2kΩ  

R(25°C)=10kΩ R(10°C)=19.1kΩ  

until the lock symbol appears.  

3700  

flashing.  

4.Sensor selection  

Tap ▲ or ▼ to select Key Lock.  

Tap OK to enter the key lock setting.  

Tap OK to confirm.  

Tap OK to return to the interface showing the real-time temperature.  

Cancel the key lock mode:  

In addition to the floor sensor, this thermostat has built-in sensors to detect room temperature.  

Therefore, three sensor applications are available:  

Symbols  

Room: Controls room temperature based solely on built-in sensors.  

Floor: Controls the floor temperature based solely on the floor sensor.  

Room.Limit: Controls the room temperature based on the built-in sensor while monitoring the floor  

temperature not to exceed the upper limit. This application, like Floor, can be used in places such as  

wood floors where floor temperature is critical.  

Under real-time temperature interface, press and hold  

disappears.  

until the lock mark on the screen  

4. Fit the left side of the front and rear covers as shown.Rotate to  

the right again and press the upper half of the right  

border until you hear a click. Use a screwdriver to  

secure the bottom screw. Turn on the power and  

test the GFCI function.  

1 On/Off/GFCI reset button  

2 GFCI test button  

3 Mode  

6 WiFi indicator  

7 Setpoint  

8 Event  

Weekly program parameter setting  

In the automatic mode, the thermostat runs automatically according to the setting parameters of the  

Sensor Selection setting method:  

After entering Settings, tap ▲ or ▼ to select Sensor Selection  

Tap OK to enter the selection.  

Tap ▲ or ▼ to select the sensor application type.  

Tap OK to confirm.  

Tap OK to return to the real-time temperature interface.  

.

weekly program. The weekly program parameters contain two parameters: Schedule and Event.  

4 Temperature  

5 Sensor selection  

9 Day and time  

10 Touch key  

1. Schedule  

WARNINGS  

Assign seven days a week to the following two schedules:  

5+1+1: The Event parameter is the same from Monday to Friday, with separate Event parameters  

on Saturday and Sunday.  

To avoid risk of electric shock, disconnect all power coming to  

heater at main service panel before installation of the thermostat. Keep air vents of thermostat clean  

and free from obstructions. All wiring must conform to local and national electrical codes and  

ordinances. Installation must be carried out by qualified personnel.  

Note: If Room.Limit is selected, you need to set the maximum temperature that the floor can accept.  

7: With separate Event parameters every day.  

5. Calibration  

Schedule parameter setting method:  

Under real-time temperature interface, tap OK to enter the first level menu, and Mode is flashing.  

Tap ▲ or ▼ to select Schedule.  

Tap OK to enter the parameter settings.  

Tap ▲ or ▼ to select a parameter.  

Tap OK to confirm.  

Ground Fault Circuit Interrupter (GFCI)  

This thermostat has built-in probe and floor sensor calibration function. In the case of demand for  

higher precision  

Calibration setting method:  

After entering Settings , tap ▲ or ▼ to select Calibration .  

This thermostat has a built-in GFCI function that protects people from electric shock. It is very  

important to check whether the GFCI function is normal or not every month. Here are the check  

steps:  

Classification  

The thermostat is a Class II device (reinforced insulation) and used for controlling electrical floor  

heating. The product must be connected to the following leads:  

L/N lead: Connect the power cord using the terminal block.  

L1/N1 lead: Use a terminal block to connect the load line(Max 15A).  

Note:  

Tap OK to go to select Room or Floor .  

Tap ▲ or ▼ to select Compensate Built-in Probe or Floor Sensor.  

Tap OK to enter the compensation setting.  

Tap ▲ or ▼ to adjust the real-time temperature to match the displayed temperature value of the  

calibration instrument.  

Tap OK to return to the setting item selection.  

1. Confirm that the thermostat is turned on.  

2. Press the [Test Monthly] button. If a red light appears in the upper left corner of the  

Tap  

to return to the real-time temperature interface.  

OK  

thermostat and GROUND FAULT appears on the screen, the GFCI function is normal. If there is  

no response, it means the function is invalid, please contact the dealer or electrical installer.  

Note: Do not press and hold the [Test Monthly] button.  

Electric floor heating cable/mat must be in accordance with the supply voltage.  

The terminals are designed to handle a cross-section of wire measuring 12-22AWG.  

2. Event  

In the Home scenario, the day is divided into four events: Wake--  

(In the Office scene, the day is divided into two phases: on work--  

temperature for each stage can be set separately.  

Leave--  

off work-- ). The set  

Return--  

Sleep--  

3. Press the [Reset] button. The red light is off and the screen shows the power off state.  

4. Press the [Reset] button again. The thermostat is turned on.  

Technical specification  

Supply voltage:  

GFCI:  

6. Location  

This thermostat is suitable for use in both homes and offices. For the office, a set of weekly  

program parameters is built in. See the Weekly Program Parameters section for details.  

Location setting method:  

After entering Settings, tap ▲ or ▼ to select Location.  

Tap OK to go to select Office or Home.  

Tap ▲ or ▼ to select one.  

Event parameter setting method:  

Under real-time temperature interface, tap OK to enter the first level menu, and Mode is flashing.  

Tap ▲ or ▼ to select Event.  

Tap OK to enter the week selection.  

Tap ▲ or ▼ to select the day you want to modify the parameters.  

Tap OK to enter the stage selection for the day.  

If in daily use, the red light is on and the screen appears GROUND FAULT. Then you need to  

check if the ground fault is present by pressing the [Reset] button. If the red light is off and the  

screen shows the shutdown status, it is nuisance tripping. If not, it means that ground fault has  

occurred. Please contact your dealer or professional technician immediately.  

120/240 VAC 50/60 Hz  

Class A (5 mA trip level)  

Load:  

Setpoint range:  

max.15 A (resistive load)  

+5 to +40°C / +41 to +104°F  

Temperature range: +5 to +45°C / +41 to +113°F  

Dimension(Inch)  

Tap OK to confirm.  

WiFi connection(Only for ET-72GW)  

Tap ▲ or ▼ to select the stage that you want to modify the parameters.  

Tap OK to enter the temperature setting of the current phase.  

Tap ▲ or ▼ to select the temperature value you want to set.  

Tap OK to enter the hour setting for the start time of the current phase.  

Tap ▲ or ▼ to select the hour of the start time.  

Tap OK to enter the minute setting for the start time of the current phase.  

Tap ▲ or ▼ to select the minute of the start time.  

Tap OK to return to the stage selection for the day.  

Tap OK to return to the real-time temperature interface.  

Step 1: Scan the QR code or download Warmme from APP store/Google browser.  

7.Adaptive  

This thermostat has an adaptive function. When this function is enabled, the thermostat heats up or  

stops heating in advance so that the next stage comes and the temperature just reaches the set  

temperature.  

Adaptive setting method:  

After entering Settings, tap ▲ or ▼ to select Adaptive.  

Tap OK to enter the selection.  

Step 2: Register and log in with mobile number  

or email address in the APP.  

Attention: Please read and agree “Privacy Policy  

and Service agreement” before registration.  

Note: Return to the interface of the real-time temperature and tap  

multiple times.  

Press ▲ or ▼ to get Yes or No.  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Warmme ET-72G(W) Thermostat User Manual
Make	Warmme
Language	English
Filetype	PDF (Download)
File size	0.68 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• Warmme

Warmme ET-72G(W) Thermostat User Manual Overview

Summary of Contents

• Page 1: This thermostat has the function of calculating the percentage of heating time over a period of time. The relevant parameters can be queried through the Readout item. After entering Settings, tap ▲ or ▼ to select Readout. Tap OK to enter the selection. This thermostat has the function of restoring factory parameters. Factory Reset setting method: After entering Settings, tap ▲ or ▼ to select Factory Reset. Tap OK to confirm. Settings contains the following items: Time, Sensor Type, Sensor Selection, Calibration, Location. The thermostat provides a key lock function to prevent the thermostat setting parameters from being incorrectly modified. This thermostat has built-in probe and floor sensor calibration function.