heatit Z-TRM6 DC Z Wave Electronic Thermostat Instruction Manual
4. QUICK START
24VDC
1. Switch off the mains voltage (disable the fuse).
2. Open the junction box.
3. Connect the wires according to the description in
Chapter 6; ”Connections”. Optional: Connect external wired
sensors.
4. After verifying the connections, switch on the mains voltage.
5. Set the primary controller in add mode (security/non-
security).
6. Hold the Center button until “OFF” is shown in the display
(approx. 5 seconds).
7. Press the ”+” button once to reach “CON”, and hold the
center button until the display shows a rotating light pattern.
8. The thermostat will display “INCL” when the thermostat is
successfully added. NB! If adding/removing fails, Err (error)
will appear.
NTC
NTC
5. INSTALLATION DISCLAIMER
Installation must be done by a qualified electrician in
accordance with national building codes. Before installation,
disconnect the power to the device from the mains. During
installation of the device, power to the device must be
disconnected AT ALL TIMES!
6. CONNECTIONS
Max tightening torque for terminal screws: 2Nm.
If the cable used has multiple strands, using a end sleeve is
advised.
The product allows for wiring of cables with a cross section of
up to 1x2.5mm2.
Potential-free input
e.g. for boiler control
The screw terminals are located at the back of the device, and
are accessable at all times.
Floor sensor
NTC type 6.8, 10, 12, 15, 22, 33, 47 or 100kΩ.
Default 10kΩ.
External sensor NTC type 6.8, 10, 12, 15, 22, 33, 47 or 100kΩ.
Default 10kΩ.
Out
In
Output.
NTC
NTC
Input.
N
Power connection (Neutral) 230VAC.
Power connection (Live) 230VAC.
L
7. INSTALLATION
Potential-free
input
To install the thermostat in the junction box, hold the sides of
the display and gently pull outwards to detach the front piece.
Connect all wires according to the correct diagram. Align the
thermostat with the junction box mounting screws, and mount
it into the junction box using 2 screws. Position the thermostat
front over the part mounted in the junction box, then carefully
press the front until it clicks into place.
| General | Details |
|---|---|
| Name | heatit Z-TRM6 DC Z Wave Electronic Thermostat Instruction Manual |
| Make | HEATIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 4.1 MB |
(1 votes, average: 5.00 out of 5)
Loading...
HEATIT Z-TRM3 Thermostat User Guide
Heatit Z-TEMP2 Thermostat Installation Guide
heatit Z-TRM3 WiFi Thermostat Instruction Manual
HEATIT Z-Temp3 is a Battery Operated Thermostat Instruction Manual
4512673 Heatit ZM Thermostat 16A User Guide
HEATIT Z-TRM6 Matt Z-Wave Thermostat User Guide
HEATIT 54 304 59 DIN Smart Thermostat Installation Guide
HEATIT 54 305 41 WiFi6 Thermostat Installation Guide
HEATIT Z-TEMP3 Thermostat User Guide
heatit ET-7AW Touchscreen Programmable Thermostat User Manual
Honeywell Home T10 Smart Home Thermostat Instructions
Honeywell DT4 Room Thermostat User Manual
Raychem Elexant 450c Thermostat Instruction Manual
GENERAL LIFE SOLARA 330S RF Digital Room Thermostat User Manual
Honeywell RCHT8610WF T5 Plus Smart Thermostat Installation Guide
GENERAL LIFE SENNA 270S Digital Room Thermostat User Manual
brennenstuhl HTCZ01 Zigbee Radiator Thermostat Instruction Manual
Danfoss UT 72-UT 73 Universal Thermostat Installation Guide
Danfoss ECtemp 130 Electronic Thermostat Installation Guide
ESi ESRTP4RFW Programmable Room Thermostat Installation Guide