Heatit Z-TEMP2 Thermostat Installation Guide
Parameter 5, Parameter Size 2. Humidity offset settings
Offsets the measured relative humidity. NB! To set negative values; 65 535 – desired value + 1.
Parameter 14, Parameter Size 2. Report when presence is detected
Decides if the thermostat sends temperature when presence is detected.
VALUE
READ- ADVANCED ALTERING
DESCRIPTION
VALUE
READ- ADVANCED ALTERING
DESCRIPTION
ONLY
CAPABILITIES
ONLY
CAPABILITIES
-100 to 100
0
0
0
-10 to 10%
(Default 0, 0%)
0
Do not report to
gateway when
presence is detected,
only at interval.
(Default)
0
0
0
Parameter 6, Parameter Size 2. Proximity sensor retrigger interval
1
Send temperature
report to gateway
when presence is
detected.
VALUE
READ- ADVANCED ALTERING
DESCRIPTION
ONLY
CAPABILITIES
2 to 270
0
0
0
2 to 270 seconds
(Default 10, 10 seconds)
18. OPERATING THE DEVICE
No Multi Channel support/ Multichannel support:
Parameter 7, Parameter Size 2. Proximity sensor Enable / Disable
Choose if proximity sensor is used or not.
Besides the mandatory command classes, Heatit Z-Temp2 has
support for following command classes:
VALUE
READ- ADVANCED ALTERING
DESCRIPTION
ONLY
CAPABILITIES
0
1
Disable
Thermostat Mode
0
0
0
Enable (Default)
It is possible to change the operating mode of the thermostat by sending
a Thermostat Mode Set command.
Parameter 8, Parameter Size 2. LED maximum brightness
Adjust the backlight of LCD display.
Uses the following values;
0x00 = OFF (Thermostat regulation is deactivated)
0x01 = Heating Mode (Thermostat regulation is active)
VALUE
READ- ADVANCED ALTERING
DESCRIPTION
ONLY
CAPABILITIES
0 to 99
0
0
0
0 to 99%
(Default 50, 50%)
Thermostat Setpoint Command Class
When a Thermostat Setpoint Set command is received by the root device,
it sets the actual setpoint for heating mode.
Parameter 9, Parameter Size 2. LED turned on before timeout
Adjust the time from proximity sensor / display touched until display goes to sleep.
VALUE
READ- ADVANCED ALTERING
DESCRIPTION
Basic Command Class
ONLY
CAPABILITIES
A Basic Set to the root endpoint will change the thermostat mode.
Uses the following values;
3 to 300
0
0
0
3 to 300 seconds
(Default 3, 3 seconds)
0x00 = OFF (Thermostat regulation is deactivated)
0x01 = Heating Mode (Thermostat regulation is active)
Parameter 10, Parameter Size 2. Temperature Control Hysteresis
Adjust the delta values for the thermostat to turn on off heating.
VALUE
READ- ADVANCED ALTERING
DESCRIPTION
Multilevel Sensor Report
ONLY
CAPABILITIES
The device sends Multilevel Sensor Reports to indicate measured
temperature and relative humidity. The device will send a humidity and
temperature report when powered on after a powerloss.
3 to 30
0
0
0
0.3 to 3°C
(Default 5, 0,5°C)
Parameter 11, Parameter Size 2. Minimum Temperature Limit
Set the mimum temperature limit.
USE CASE
SENSORTYPE
SIZE
SCALE
PRECISION
Sends tempe- Temperatu-
2Byte = 0x02
Celsius (°C)
= 0x00
1 decimal
= 0x01
VALUE
READ- ADVANCED ALTERING
DESCRIPTION
rature report
from internal
sensor
re(version 1)
= 0x01
ONLY
CAPABILITIES
50 to 400
0
0
0
5 to 40°C
(Default 50, 5°C)
Sends relative Relative humi- 2Byte = 0x02
humidity
Percentage
value (%)
=0x00
1 decimal
= 0x01
dity (version 2)
= 0x05
report from
internal sensor
Parameter 12, Parameter Size 2. Maximum Temperature Limit
Set the maximum temperature limit.
VALUE
READ- ADVANCED ALTERING
DESCRIPTION
ONLY
CAPABILITIES
Notification Command Class
50 to 400
0
0
0
5 to 40°C
(Default 400, 40°C)
When the device is turned back on after a power outage (insearted
fresh batteries), the device sends a notification command to indicate
that the device is back in idle state. The Device will also send a
humidity report and temperature report when powered back on.
Parameter 13, Parameter Size 2. External Relay & Operating State update interval
Set time on how often the devices sends Binary Switch Set and thermostat mode to gateway.
VALUE
READ- ADVANCED ALTERING
DESCRIPTION
EVENT
TYPE
EVENT
LENGTH
ONLY
CAPABILITIES
Power On (OxFF)
Power maneg-
ment (0x08)
Power has been
applied (0x01)
0x00
0
Sends only when
changed (Default)
0
0
0
1 to 240
1 to 240 minutes +
When changed
| General | Details |
|---|---|
| Name | Heatit Z-TEMP2 Thermostat Installation Guide |
| Make | HEATIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.23 MB |
(1 votes, average: 5.00 out of 5)
Loading...
heatit Z-TRM6 DC Z Wave Electronic Thermostat Instruction Manual
HEATIT Z-TRM3 Thermostat User Guide
heatit Z-TRM3 WiFi Thermostat Instruction Manual
HEATIT Z-Temp3 is a Battery Operated Thermostat Instruction Manual
4512673 Heatit ZM Thermostat 16A User Guide
HEATIT Z-TRM6 Matt Z-Wave Thermostat User Guide
HEATIT 54 304 59 DIN Smart Thermostat Installation Guide
HEATIT 54 305 41 WiFi6 Thermostat Installation Guide
HEATIT Z-TEMP3 Thermostat User Guide
heatit ET-7AW Touchscreen Programmable Thermostat User Manual
warmup RFT-P Programmable Radiant Floor Thermostat User Manual
TechPunt E1 Smart WiFi Radiator Thermostat User Guide
expert4house BHT-8000 Heating Thermostat User Guide
BlueLink 8205 Smart Wi-Fi Thermostat User Manual
Smart Radiator Thermostat Expansion Instruction Manual
Honeywell VisionPRO Series 7 Day Programmable Thermostat User Guide
Zhongjin STN731RF Thermostat Instruction Manual
Quality Heating PRF-80 Touch Thermostat Instructions
Honeywell RLV450 Programmable Thermostat
Beca BHT-002 Electric Heating Wifi Thermostat User Guide