heatit WiFi TRM3 Intelligent Smart Home Thermostat User Guide
For further information on installing, setting up and using your Heatit
WiFi thermostat, see the complete manual on manuals.heatit.com.
HEATIT WIFI
Quick Guide
01.10.21 Ver 2021-A
Read the full manual at:
manuals.heatit.com
TECHNICAL DATA
Protocol
WiFi 2.4GHz 802,11bgn
1.8”TFT, 128x160 resolution
230VAC 50Hz
Display
Rated voltage
Max load
Release the front cover by pressing a screwdriver (e.g) into the ejector
latch at the bottom of the thermostat. Be careful not to damage the
thermostat.
3600W (resistive loads only)
Recommends contactor for
loads higher than 13A
16A
Max current
Connect the wires to the thermostat terminals:
Power consumption <2W
L
Power connection (Live) 230VAC
Ambient temperature 2°C to 30°C
LOAD (N) Heating Cable connection (Neutral)
LOAD (L) Heating Cable connection (Live)
Temperature range
Hysteresis
5°C to 40°C
0.2°C to 2°C (0.5°C standard)
N
Power connection (Neutral) 230VAC
Pilot Wire (if applicable) 230VAC
Floor temp sensor, NTC type
Compatible with NTC
sensors with value
IP Code
PILOT
SENSOR
6.8, 10, 12, 15, 22, 33, 47, 100 kΩ @ 25°C
IP 21
INTRODUCTION
Heatit WiFi thermostat is an electronic thermostat for electrical
underfloor heating. The thermostat has a simple user interface and
can be easily programmed via the capacitive buttons. The color screen
displays an accessible user interface. The thermostat has a built-in WiFi
chip that allows you to control it from a user-friendly app. The ”Heatit
WiFi”app is available on Google Play and in the App Store. Works
with Amazon Alexa and Google Home (pending). If you are installing
multiple thermostats in the same house, you may copy the settings
from one thermostat to the next. This simplifies installation.
Next, position the thermostat and fasten it onto the wall mounting box
using 2-4 screws. Open the frame holder spring, position the frame and
reattach the spring. Then attach the front, making sure the connectors
between the front and back are correctly placed. Press the front carefully
until it snaps into place.
Approvals
EN 60730-1:2016, EN 60730-2-9:2019,
ETSI EN 300 328 V2.2.2, RoHS 2011/65/EU,
LVD 2014/35/EU
Approved for use in bathrooms.
STARTUP
After connecting the power to the thermostat for the first time or after
performing a factory reset, the startup wizard will prompt the following
questions:
PHONE APPLICATIONS
Heatit WiFi thermostat 16A is equipped with a single-pole switch and
fits into most common frames (e.g. System 55, Elko RS16, Schneider
Exxact). The thermostat can withstand a load of max 16A/3600W
at 230VAC. We recommend a contactor for loads above 13A. The
thermostat may be connected to an external sensor.
Language
Set language
Timezone compared to GMT
Daylight saving in use Y/N
Set timezone
Daylight saving
Date & time
Set current date & time
Thermostat use
Heating system
Floor type
Heating or Cooling
Floor (Slow), Floor (Fast), Other (Fast)
Concrete or wooden
The thermostat is designed for electrical heating.
Floor temp limit
Choice of sensor
Gradual Heating
5°C - 40°C (concrete) or 5°C - 27°C (wood)
Room/Floor
ON or OFF - used with new concrete floors to limit
temperature rise time. Only in floor sensor mode.
INSTALLATION
Installation must be done by a qualified electrician in accordance with
national building codes. Before installation, disconnect the power to the
device from the mains. During installation of the device, power to the
device must be disconnected AT ALL TIMES!
App Store
Play Store
WIFI CONNECTIONS
Heatit Controls AB can not be held liable for typographical errors, other errors or
omittances in our information. Product specifications may change without further notice.
All electrical installations must be carried out by a licensed electrician. The product must
be installed in accordance with national building codes and our installers manual.
Start the ”Connect to cloud”process from the WiFi settings menu.
Launch ”Add thermostat”in the app on your phone. The thermostat will
show two 3-digit PIN codes. Enter these into your phone application.
Next, enter your WiFi password in your app. When the ”Add thermostat”
process is finished, the thermostat will reboot. Subsequently, you will be
able to control your thermostat WiFi settings through the app on your
phone.
Heatit Controls AB
Phone: +47 61 18 77 77
l
Läkarvägen 4, 454 31 BRASTAD, SWEDEN
post@heatit.com – www.heatit.com
l
| General | Details |
|---|---|
| Name | heatit WiFi TRM3 Intelligent Smart Home Thermostat User Guide |
| Make | HEATIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.12 MB |
(1 votes, average: 5.00 out of 5)
Loading...
heatit Z-TRM6 DC Z Wave Electronic Thermostat Instruction Manual
HEATIT Z-TRM3 Thermostat User Guide
Heatit Z-TEMP2 Thermostat Installation Guide
heatit Z-TRM3 WiFi Thermostat Instruction Manual
HEATIT Z-Temp3 is a Battery Operated Thermostat Instruction Manual
4512673 Heatit ZM Thermostat 16A User Guide
HEATIT Z-TRM6 Matt Z-Wave Thermostat User Guide
HEATIT 54 304 59 DIN Smart Thermostat Installation Guide
HEATIT 54 305 41 WiFi6 Thermostat Installation Guide
HEATIT Z-TEMP3 Thermostat User Guide
homematic IP IP HmIP-eTRV-CL Radiator Thermostat Instruction Manual
HELTUN Fan Coil Thermostat HE-FT01 User Manual
GENERAL LIFE HT300 RF Digital Room Thermostat User Manual
SECURE ThermoPlus AS2 Programmable Room Thermostat Instruction Manual
ENGO CONTROLS EONEBATW, EONEBATB Internet Controlled Thermostat User Manual
QUIETWarmth Type UCG Thermostat User Manual
HEIL TSTATIIEWF-01 Smart Thermostat Owner’s Manual
WarmlyYours TH115-AF-GA-08 SmartStat TH115 Series Thermostat Instruction Manual
DAIKIN IM 1368 Vertical Stack WSHP Thermostat Instruction Manual
TAELEK DIN-3-W Tsense Thermostat for DIN Rail Instruction Manual