Amana DS01G Digi Smart Thermostat Instruction Manual
The display will alternate between displaying the feature
code and the option code 0 (factory default setting).
Press the HEAT button one time to get into C1 mode
and then the display will alternate between C1 and 0 -
the factory default. If an RF DS01* has been bound to
the unit the display will alternate between C1 and rE.
The lower right dot on the display will flash.
up and down
arrow keys to select
(
=
appears in the display).
For the bedroom unit closest to the main room in room
224, press the up and down
arrow keys to select
DP01* or DL01E
Entering Room Number (Skip if not using
=
02
(
appears in the display) Press the
DP01* Front Desk Platform)
key to exit configuration mode.
1. The PTAC control can be set for a 4-digit room
number. To select the first two digits (floor), press
Binding of RF Devices
the HEAT
key until
appears, then press
the up
down arrows to select the first two digits.
2. To select the last two digits of the room number,
press the HEAT
key until
appears, then
IMPORTANTNOTE:IfwirelessplatformDP01*orDL01Eare
beingutilized,thenroomnumbersMUSTBECONFIGUREDin
the control board prior to binding wireless devices.
press the up and down
arrows to select the last
DO NOT ATTEMPT TO BIND
MORE THAN ONE ROOM AT A TIME AT THE
SAME PROPERTY!!!
2 digits of the room number.
For example for Room “201”, press the HEAT
key until appears, then press the
RF TRANSMITS THROUGH WALLS.
up
down arrows to select “02”:
Next to select the last two digits of the room
number, press the HEAT key until
=
.
The wireless devices (DS01G and or DD01E must be bound
tothePTACDT01*controlforproperin-roomcommunication.
Ensure the unit is powered but in the OFF position.
NOTE: Both the DS01Gand the DD01E must be bound to
appears, then press the up and down
select “01”:
arrows to
thePTACunitduringthesame“learn”operation.
If you need to rebind one device - then you
must rebind both devices during the same
learn mode event.
=
.
3. If a room contains more than one unit (a suite), a suffix
must also be entered to identify which unit is in the
All must be bound at one time.
1. Press and hold OFF button on the PTAC until appears.
main room and which unit(s) are in bedroom(s). Master
unit ALWAYS MUST have a 01 suffix and slaves a suffix
or 02, 03, etc. To select the room # suffix, while still in
2. Press and then immediately release the white tactile
button on the back of the DS01* thermostat.
now be displayed on the PTAC LED display. If
should
does
configuration mode, press the HEAT
key until
not show on the display in 1-2 seconds, then press and
release the white button a second time. Skip this step
if there is no thermostat.
appears. Then press the up and down
arrows
3. Press and then immediately release the white tactile
to select the room # suffix. Example: For the unit
serving the main living area in room 224, press the
button on the back of the DD01* motion sensor.
or
should now be displayed on the PTAC LED display.
HEAT
key until
appears, then press the
10
| General | Details |
|---|---|
| Name | Amana DS01G Digi Smart Thermostat Instruction Manual |
| Make | Amana |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.66 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Amana MMW-2 Horizontal Digital Wireless non EMS Wall Thermostat Instruction Manual
Amana ATST-CWE-BL-A Smart Thermostat Owner’s Manual
Amana DS01 PTAC Wireless Thermostat User Manual
CENTER EHE0200123 Wired 7 Day Programmable Thermostat Installation Guide
Honeywell TC500A-N Commercial Thermostat User Guide
Danfoss 088N3688 Room Thermostat Installation Guide
Danfoss INT69 Thermal Protection Thermostat Instruction Manual
PROSELECT PSTSN11AWH Non Programmable Thermostat Installation Guide
EPH CONTROLS RFC-RF RF Room Cylinder Thermostat Instruction Manual
stelpro STZB402+ ELECTRONIC THERMOSTAT FOR THE SMART HOME User Guide
PRO1 T771 Programmable Electronic Thermostat Instructions
Mi-Heat GH35EU Digital Greenhouse Thermostat User Manual
RITTAL SK 3114.200 Digital Enclosure Internal Temperature Display and Thermostat Instructions