Amana DS01G Digi Smart Thermostat Instruction Manual
6B. Drill a 7/32” holes and tap plastic anchors into wall.
Screw mounting base plate to wall. DO NOT SNAP
THERMOSTAT INTO PLACE UNTIL AFTER BINDING
PROCESS. See Binding Instructions on page 10. Proceed
to Step 7.
Thermostat Installation for DS01G Kit
NOTE: A DT01* must be installed on the digital PTAC unit
for the DS01* to be operable.
Skip these steps if not installing.
4C. If mounting thermostat to one or two gang
electrical box, discard flush-mount base extension.
Screw mounting base plate to electrical box.
Screws not included. DO NOT SNAP
THERMOSTATINTO PLACE UNTILAFTER
BINDING PROCESS. See Binding Instructions on
page 10.
1. Select thermostat mounting location about five feet
above the floor, on an inside wall, out of direct sunlight,
away from sources of radiant heat (lamps, fireplaces,
heating and air conditioning equipment, etc.), away
from windows or door to the outside, and avoid areas
with poor air circulation. If the PIR in the thermostat is
to be used with a DD01* device as a 2nd motion sensor,
point the thermostat towards the area where you are
requiring additional motion sensing.
7. Install two (2) AA batteries (included) into the back of
the thermostat. Terminals are marked “+” and “-” for
polarity.
Ensure location is out of the path of foot traffic where
a person might accidentally bump into the thermostats
and damage the device.
NOTE: Do not install thermostat on wall plate until all
configuration settings and binding processes have been
completed.
2. Set flush-mount base extension aside from mounting
base plate.
WIREDPOWEROPTION
3. Remove thermostat from mounting base plate by gently
pulling apart at the bottom of the thermostat about 1”,
and slide thermostat up to release from the top of the
mounting base plate. If mounting thermostat flush to
wall proceed to step 4A. If mounting thermostat with
battery compartment recessed into drywall proceed to
step 4B, or if mounting thermostat to an electrical box
proceed to step 4C.
1. If the option for wired power is used, the two thermostat
wires (20 gauge minimum field supplied) can be
connected to the thermostat.
2. Route wires through the rectangular opening on the flush
mount base plate base extension if used, and through
the label in the area marked by a circle on the mounting
base plate.
4A. Place flush-mount base extension against the wall
at desired location and mark placement of the right
mounting hole and top mounting holes. Make sure
rectanglular opening is on the left side so that when
mated with the mounting base plate the UP arrow is
pointing up on the mounting base plate.
3. Loosen set screws on wired terminals labeled 24VAC and
insert wires into the opening. Tighten set screws. (See
following figure for powered connection with 2 jumpers).
Move jumper from the two pins furthest from the battery
block to the two pins nearest the battery block.
5A. If mounting in drywall, drill 7/32” holes, tap plastic
anchors into wall. For other surfaces, drill hole as
required.
4. Connect wires at PTAC unit to terminal pins C and R.
The wire harness kit PWHK01C is required for this
connection.
6A. Screw mounting base plate and flush-mount base
extension assembly to the wall. DO NOT SNAP
THERMOSTAT INTO PLACE UNTIL AFTER BINDING
PROCESS. See Binding Instructions on page 10.
Proceed to step 7.
WIRED DOOR SWITCH OPTION
NOTE: Thermostat has motion sensing capability for
energy management operation, and thermostat may be
connected to a wired door switch or may work in
conjunction with a wireless door switch or wired door
switch connected to the PTAC.
4B. If mounting thermostat with battery compartment
recessed into drywall, cut drywall opening 2” wide
by 2&7/8” tall in desired location. The flush-mount
base extension may be used as a template. Due
care should be taken if wiring, plumbing or other
contents behind the wall are unknown.
1. If connecting a wired door switch to this thermostat (20
gauge minimum field supplied) can be connected to
the thermostat.
5B. Discard flush-mount base extension. Place the
mounting base plate against the wall in the desired
location and mark placement of right mounting hole
and top mounting hole. Make sure the UP arrow is
pointing up on the mounting base plate.
2. Route wires through the rectangular opening on the
flush mount base plate base extension if used, and
through the label in the area marked by a circle on
the mounting base plate.
3
| General | Details |
|---|---|
| Name | Amana DS01G Digi Smart Thermostat Instruction Manual |
| Make | Amana |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.66 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Amana MMW-2 Horizontal Digital Wireless non EMS Wall Thermostat Instruction Manual
Amana ATST-CWE-BL-A Smart Thermostat Owner’s Manual
Amana DS01 PTAC Wireless Thermostat User Manual
KETOTEK LL0269 WiFi Digital Heating Thermostat User Manual
SCHRACK TECHNIK EV103311 Analog Thermostat User Manual
EPH CONTROLS eTRV Smart Radiator Thermostat Instruction Manual
MOES ZTRV-BY-100 Radiator Thermostat User Guide
DEVI 532 Electronic Thermostat Installation Guide
SALUS HTRS-RF Wireless Digital Thermostat Instruction Manual
emos P56211 Wireless Room Thermostat Instruction Manual
HIVE HAH2INSTAMZ-01 Active Heating Thermostat User Guide
SALUS CONTROLS T105 Digital Programmable Thermostat User Guide
Stelrad Radiator Thermostat RAS-D2 Combi Pack, Radiator Pack Instructions