STELPRO SIBTE13F Electronic Thermostat User Guide

1

OWNER’S GUIDE  

INSTALLATION  

OPERATING INSTRUCTIONS  

3 BUTTONS TO CONTROL THE TEMPERATURE  

ASSEMBLE THE  

THERMOSTAT  

PREPARE THE BASEBOARD  

Press to lower the setpoint  

temperature by 1°  

Press to set the setpoint  

temperature to 70°F (20°C)  

Press to raise the setpoint  

temperature by 1°  

2

1

1. Attach the thermostat using the screws  

provided.  

2. To ensure proper grounding and heat transfer,  

make sure the thermostat is screwed in  

securely and is in contact with the junction  

box cover.  

WARNING: Turn off the power supply. Do not install the thermostat  

in a position other than that indicated in this guide.  

BUILT-IN ELECTRONIC THERMOSTAT FOR  

BRAVA AND PRIMA ELECTRIC BASEBOARDS  

1. Choose which side of the baseboard to install the thermostat. The connection must  

be made in the same junction box as the power supply.  

2. Remove the front panel. Refer to the baseboard instructions for more details.  

3. Unscrew the front cover of the junction box [A] and remove it.  

4. Remove the knockouts [B] with a hammer and a screwdriver.  

Model C (Celsius)  

SIBTE12C  

SIBTE12F  

SIBTE13C  

SIBTE13F  

Indicator lights  

1-844-STELPRO  

WWW.STELPRO.COM  

4

4

INITIAL SETTING  

Once installation is complete, you must configure your  

thermostat according to your baseboard model.  

B

B

IMPORTANT INSTRUCTIONS  

MODEL F  

(Fahrenheit)  

MODEL C  

(Celsius)  

INDICATOR  

LIGHTS  

BASEBOARDS  

BRAVA*  

B

Before installing or using this product, you must read and understand  

these instructions. The manufacturer cannot be held responsible for  

anything, and the warranty will not be valid if the installer and user do  

not follow these instructions. Failure to comply with these instruc-  

tions could result in bodily harm, property damage, serious injury and  

potentially fatal electric shock.  

Press simultaneously  

Press simultaneously  

Purple  

+

+

A

B

3 sec.  

3 sec.  

A

Press simultaneously  

Press simultaneously  

BRAVA  

PRIMA  

BRAVA  

PRIMA  

The thermostat must be installed by a certified electrician.  

PRIMA  

Light blue  

+

+

3 sec.  

3 sec.  

WARNING: HIGH VOLTAGE. Turn off the power supply  

before installation and maintenance.  

* By default, the thermostat is set up for the BRAVA baseboard.  

CONNECT THE POWER  

SUPPLY WIRES  

INSTALL THE TEMPERATURE SENSOR  

INDICATOR LIGHTS  

The indicator lights provide feedback on your comfort choices  

and other advanced features.  

3

4

SAVE THESE INSTRUCTIONS  

TECHNICAL SPECIFICATIONS  

Complete the thermostat’s electrical connection  

according to one of the diagrams below. Tighten  

the wires securely in the supplied connection  

caps.  

Install the temperature  

sensor [A] as shown,  

making sure it is firmly  

seated at the bottom  

of the groove.  

TEMPERATURE  

COLOUR  

BLUE  

DESCRIPTION  

Freeze protection  

Energy saving  

MODEL F (Fahrenheit)  

MODEL C (Celsius)  

41°F  

5°C  

A

GREEN  

42°F to 66°F  

67°F to 74°F  

75°F to 86°F  

6°C to 19°C  

20°C to 23°C  

24°C to 30°C  

WARNING: Be sure to connect the wire  

colours as shown in the diagrams when  

making electrical connections.  

VERSION  

VOLTAGE AND LOAD  

VOLTAGE RATING  

A

CELSIUS (°C) OR  

FAHRENHEIT (°F)  

SUPPLY VOLTAGE  

(VAC)  

OVERVOLTAGE  

CATEGORY  

GREEN TO ORANGE  

RED  

Eco-comfort balance  

Optimal comfort  

PRODUCT CODE  

LOAD (W)  

SIBTE12C  

SIBTE12F  

SIBTE13C  

SIBTE13F  

°C  

°F  

°C  

°F  

120-240  

II (1500V)  

III (2500V)  

The baseboard has overheated, and heating has been switched off.  

After four minutes, the indicator lights will turn off. Heating will be  

restored. If the indicator lights flash repeatedly, make sure nothing  

is obstructing the baseboard. Otherwise, contact °STELPRO.  

300-2500  

WHITE  

SLEEVE  

FLASHING RED  

277-347  

BRAVA  

PRIMA  

The baseboard isn’t operating due to a problem with  

the temperature sensor. Please contact °STELPRO.  

Built-in control device  

FLASHING YELLOW  

FLASHING WHITE  

Thermistor used as a sensor, carries no charging current  

Class A software  

Lock/unlock feature. See the section below.  

Enclosure protection rating  

Power supply type  

Load control type  

Action  

IP20  

INSTALL THE INTERFACE  

5

Device designed for alternating current only  

Resistive  

Type 1.Y  

2

ADJUSTING THE TEMPERATURE  

Here are some examples of how to use the three buttons on  

the thermostat to adjust the setpoint temperature.  

1. Make sure surfaces are clean and dry. Position the interface so that the numbers  

face in the correct direction, as shown.  

2. Remove the adhesive protection on the back of the interface.  

3. Insert the connector into the opening. Clip the interface into place and press firmly  

so that the adhesive sticks to the surface.  

4. Clip the interface connector into the thermostat connector.  

5. Push all the wires into the junction box while closing it. Be sure that the flat flexible cable  

does not interfere with the wires and that the sensor wires are not pinched by the cover  

as this could damage them.  

6. Screw the junction box cover back on, then replace the front panel.  

7. Restore the power supply.  

YELLOW  

RED  

Pollution level  

BLACK  

Frequency  

60 Hz  

Overload protection device external  

to the control  

Circuit breaker  

(refer to local electrical code)  

DESIRED TEMPERATURE  

72 °F*  

PRESS  

INDICATOR LIGHTS  

Operating temperature  

Storage temperature  

-20°C to 65°C (-4°F to 149°F)  

-40°C to 65°C (-40°F to 149°F)  

Orange  

BRAVA  

67 °F*  

Green  

Blue  

41 °F*  

Freeze protection  

WHITE  

SLEEVE  

3 sec.  

LIMITED °STELPRO WARRANTY  

* Celsius version on the back.  

3

3

4

Limited three-year warranty. See details on www.stelpro.com  

LOCK/UNLOCK FEATURE  

PRESS  

INDICATOR LIGHTS  

WHAT’S IN THE BOX  

One (1) thermostat, one (1) control interface, two (2) screws,  

three (3) twist-on wire connector, one (1) white sleeve  

Press simultaneously  

RED  

LOCK  

After 3 sec., 3 white flashes  

+

YELLOW  

After 3 sec., display of the  

current setpoint color  

UNLOCK  

3 sec.  

BLACK  

When an attempt is made to change the setpoint while in lock mode,  

the indicator lights will flash white three times.  

MATERIAL REQUIRED  

Hammer, #2 Phillips or #2 Robertson screwdriver  

PRIMA  

BRAVA  

PRIMA  

For more information, watch the video at: WWW.STELPRO.COM  

Saint-Bruno-de-Montarville, Quebec, Canada, J3V 6L7  

STELPRO DESIGN INC.  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	STELPRO SIBTE13F Electronic Thermostat User Guide
Make	StelPro
Language	English
Filetype	PDF (Download)
File size	0.77 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• StelPro

STELPRO SIBTE13F Electronic Thermostat User Guide Overview

Summary of Contents

• Page 1: owner’s guide installation operating instructions 3 buttons to control the temperature assemble the thermostat prepare the baseboard initial setting important instructions the thermostat must be installed by a certified electrician. limited °stelpro warranty