STELPRO SIBTE13F Electronic Thermostat User Guide
OWNER’S GUIDE
INSTALLATION
OPERATING INSTRUCTIONS
3 BUTTONS TO CONTROL THE TEMPERATURE
ASSEMBLE THE
THERMOSTAT
PREPARE THE BASEBOARD
Press to lower the setpoint
temperature by 1°
Press to set the setpoint
temperature to 70°F (20°C)
Press to raise the setpoint
temperature by 1°
2
1
1. Attach the thermostat using the screws
provided.
2. To ensure proper grounding and heat transfer,
make sure the thermostat is screwed in
securely and is in contact with the junction
box cover.
WARNING: Turn off the power supply. Do not install the thermostat
in a position other than that indicated in this guide.
BUILT-IN ELECTRONIC THERMOSTAT FOR
BRAVA AND PRIMA ELECTRIC BASEBOARDS
1. Choose which side of the baseboard to install the thermostat. The connection must
be made in the same junction box as the power supply.
2. Remove the front panel. Refer to the baseboard instructions for more details.
3. Unscrew the front cover of the junction box [A] and remove it.
4. Remove the knockouts [B] with a hammer and a screwdriver.
Model C (Celsius)
SIBTE12C
SIBTE12F
SIBTE13C
SIBTE13F
Indicator lights
1-844-STELPRO
WWW.STELPRO.COM
4
4
INITIAL SETTING
Once installation is complete, you must configure your
thermostat according to your baseboard model.
B
B
IMPORTANT INSTRUCTIONS
MODEL F
(Fahrenheit)
MODEL C
(Celsius)
INDICATOR
LIGHTS
BASEBOARDS
BRAVA*
B
Before installing or using this product, you must read and understand
these instructions. The manufacturer cannot be held responsible for
anything, and the warranty will not be valid if the installer and user do
not follow these instructions. Failure to comply with these instruc-
tions could result in bodily harm, property damage, serious injury and
potentially fatal electric shock.
Press simultaneously
Press simultaneously
Purple
+
+
A
B
3 sec.
3 sec.
A
Press simultaneously
Press simultaneously
BRAVA
PRIMA
BRAVA
PRIMA
The thermostat must be installed by a certified electrician.
PRIMA
Light blue
+
+
3 sec.
3 sec.
WARNING: HIGH VOLTAGE. Turn off the power supply
before installation and maintenance.
* By default, the thermostat is set up for the BRAVA baseboard.
CONNECT THE POWER
SUPPLY WIRES
INSTALL THE TEMPERATURE SENSOR
INDICATOR LIGHTS
The indicator lights provide feedback on your comfort choices
and other advanced features.
3
4
SAVE THESE INSTRUCTIONS
TECHNICAL SPECIFICATIONS
Complete the thermostat’s electrical connection
according to one of the diagrams below. Tighten
the wires securely in the supplied connection
caps.
Install the temperature
sensor [A] as shown,
making sure it is firmly
seated at the bottom
of the groove.
TEMPERATURE
COLOUR
BLUE
DESCRIPTION
Freeze protection
Energy saving
MODEL F (Fahrenheit)
MODEL C (Celsius)
41°F
5°C
A
GREEN
42°F to 66°F
67°F to 74°F
75°F to 86°F
6°C to 19°C
20°C to 23°C
24°C to 30°C
WARNING: Be sure to connect the wire
colours as shown in the diagrams when
making electrical connections.
VERSION
VOLTAGE AND LOAD
VOLTAGE RATING
A
CELSIUS (°C) OR
FAHRENHEIT (°F)
SUPPLY VOLTAGE
(VAC)
OVERVOLTAGE
CATEGORY
GREEN TO ORANGE
RED
Eco-comfort balance
Optimal comfort
PRODUCT CODE
LOAD (W)
SIBTE12C
SIBTE12F
SIBTE13C
SIBTE13F
°C
°F
°C
°F
120-240
II (1500V)
III (2500V)
The baseboard has overheated, and heating has been switched off.
After four minutes, the indicator lights will turn off. Heating will be
restored. If the indicator lights flash repeatedly, make sure nothing
is obstructing the baseboard. Otherwise, contact °STELPRO.
300-2500
WHITE
SLEEVE
FLASHING RED
277-347
BRAVA
PRIMA
The baseboard isn’t operating due to a problem with
the temperature sensor. Please contact °STELPRO.
Built-in control device
FLASHING YELLOW
FLASHING WHITE
Thermistor used as a sensor, carries no charging current
Class A software
Lock/unlock feature. See the section below.
Enclosure protection rating
Power supply type
Load control type
Action
IP20
INSTALL THE INTERFACE
5
Device designed for alternating current only
Resistive
Type 1.Y
2
ADJUSTING THE TEMPERATURE
Here are some examples of how to use the three buttons on
the thermostat to adjust the setpoint temperature.
1. Make sure surfaces are clean and dry. Position the interface so that the numbers
face in the correct direction, as shown.
2. Remove the adhesive protection on the back of the interface.
3. Insert the connector into the opening. Clip the interface into place and press firmly
so that the adhesive sticks to the surface.
4. Clip the interface connector into the thermostat connector.
5. Push all the wires into the junction box while closing it. Be sure that the flat flexible cable
does not interfere with the wires and that the sensor wires are not pinched by the cover
as this could damage them.
6. Screw the junction box cover back on, then replace the front panel.
7. Restore the power supply.
YELLOW
RED
Pollution level
BLACK
Frequency
60 Hz
Overload protection device external
to the control
Circuit breaker
(refer to local electrical code)
DESIRED TEMPERATURE
72 °F*
PRESS
INDICATOR LIGHTS
Operating temperature
Storage temperature
-20°C to 65°C (-4°F to 149°F)
-40°C to 65°C (-40°F to 149°F)
Orange
BRAVA
67 °F*
Green
Blue
41 °F*
Freeze protection
WHITE
SLEEVE
3 sec.
LIMITED °STELPRO WARRANTY
* Celsius version on the back.
3
3
4
Limited three-year warranty. See details on www.stelpro.com
LOCK/UNLOCK FEATURE
PRESS
INDICATOR LIGHTS
WHAT’S IN THE BOX
One (1) thermostat, one (1) control interface, two (2) screws,
three (3) twist-on wire connector, one (1) white sleeve
Press simultaneously
RED
LOCK
After 3 sec., 3 white flashes
+
YELLOW
After 3 sec., display of the
current setpoint color
UNLOCK
3 sec.
BLACK
When an attempt is made to change the setpoint while in lock mode,
the indicator lights will flash white three times.
MATERIAL REQUIRED
Hammer, #2 Phillips or #2 Robertson screwdriver
PRIMA
BRAVA
PRIMA
For more information, watch the video at: WWW.STELPRO.COM
Saint-Bruno-de-Montarville, Quebec, Canada, J3V 6L7
STELPRO DESIGN INC.
| General | Details |
|---|---|
| Name | STELPRO SIBTE13F Electronic Thermostat User Guide |
| Make | StelPro |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.77 MB |
(1 votes, average: 5.00 out of 5)
Loading...
STELPRO STF362NP Floor Heating Thermostat Owner’s Manual
STELPRO ST302P Programmable Electronic Thermostat Owner’s Manual
STELPRO SAT402ZB Smart Thermostat User Guide
STELPRO ST252NPFF Non-Programmable Electronic Thermostat Owner’s Manual
STELPRO ST402PFF Programmable Electronic Thermostat Owner’s Manual
STELPRO ASMC402 Maestro Zigbee Smart Programmable Thermostat User Guide
STELPRO SIBTE12C Electronic Thermostat Owner’s Manual
STELPRO STZW402+ Electronic Thermostat for The Smart Home Owner’s Manual
STELPRO STCP MULTIPLE PROGRAMMING ELECTRONIC THERMOSTAT User Guide
STELPRO STCP Floor Heating Thermostat Multiple Programming User Guide
EMERSON 1F75C-11NP Non Programmable Single Stage Thermostat User Manual
EMOS P5601UF Floor Heating Thermostat User Manual
ESi ESRTP4 TOUCH Programmable Room Thermostat Instruction Manual
BeSMART 20143539 WiFi Smartphone Thermostat with Backlight User Guide
GENERAL LIFE ARUNA HT300S Digital Room Thermostat User Manual
lae AC2-2 Two Stage Thermostat Instructions
hansgrohe AXOR STARCK Concealed Thermostat with Shut Off Valve Instruction Manual
DIGITEN DTC-310 Electronic Temperature Controller Thermostat User Manual
VIMAR 02971 Smart Automation Rotary Dial Thermostat Instruction Manual
Global Sources WT598 1T1 Smart Thermostat Instructions