SALUS Wired Thermostat Installation Guide
Default
value
dxx
Function
Value
Description
Temperature setting
NSB function - automatic mode
Offset function (temperature calibration)
0
1
2
PWM algorithm
Span 0.25°C
The NSB (Night SetBack) function can automatically change temperatures
on VS35 daily thermostats via VS30 programmable thermostat connected to
a wiring centre (or another external clock). NSB function switches between
The VS35 thermostat allows you to adjust the displayed temperature 3.0°C.
You can do it according to the following steps:
Press any button to highlight the screen, then follow the steps below:
Control method
temperature
d01
0
Span 0.5°C
Press any button to highlight the screen, then follow the steps below:
comfortable temperature
and economic temperature
.
1
2
If the thermostat indica-
from -3.0°C tes wrong temperature,
to +3.0°C
To activate the automatic mode, select the
the
icon. On display together with
or
1
2
d02
d03
Offset temperature
0°C
0
icon, the controller indicates active temperature mode:
.
you can correct
it by 3.0°C
Using a floor
temperature sensor
(S1, S2)
0
1
No sensor
Press any button to highlight the screen, then follow the steps below:
Sensor is connected
1
2
Thermostat measures
the temperature only on
the external sensor
External sensor
used for air
or floor temperature
measurement
(Function is active,
when d03=1)
0
1
Current temperature.
Temperature set in the selected
operating mode.
3 sec
d04
0
The sensor is used
as a protection against
overheating the floor
3
4
3
4
1
2
0
1
0
1
Span 0.5°C
Span 1.0°C
NO - normally open
NC - normally closed
OFF
Cooling mode control
method
d05
d06
2
1
Select the automatic mode
using or buttons.
Type of thermoelectric
actuator
Note: For the NSB function to work, it is necessary to connect the wirings
properly. Connection diagrams can be found on the previous page.
d07
d08
d12
Valve protection
1
ON
Set Offset temperature value
using or buttons.
Press to confirm the changes.
Set the temperature with
or
Press to confirm the changes.
Frost protection
temperature
Frost protection / Holiday
mode temperature
buttons.
5-17°C
5-35°C
5°C
35°C
Changing the HEATING / COOLING mode
The maximum heating
temperature that can be set
by the user
Note: You can also set the Offset temperature value using the service
parameter d02.
Heating temperature
limit
Press any button to highlight the screen, then follow the steps below:
Manual mode - temperature settings
The minimum cooling
temperature that can
be set by the user
Cooling temperature
limit
d13
d14
5-40°C
6-45°C
5°C
There are
temperature level is active (icon in the frame
4
temperature levels available. In manual mode only one
indicates which mode is
1
2
Installer settings
In order to protect the
floor from overheating,
heating will be turned
OFF, when the maximum
temperature of the floor
sensor will be reached
Maximum floor
temperature
(this function is active
in heating mode when
d04 = 1)
currently choosen). For each temperature levels you can set a different
temperature.
Press any button to highlight the screen, then follow the steps below:
27°C
1
2
In order to protect
the floor, heating will
be turned ON, when the
minimum temperature
of the floor sensor will
be reached
- Comfort mode
- Standard mode
- Economic mode
Minimum floor
temperature
(this function is active
in heating mode when
d04 = 1)
3 sec
d15
6-45°C
6-45°C
10°C
3 s
3 se
3 sec
3
4
In order to protect the
floor, cooling will
be turned OFF, when
the minimum temperatu-
re will be reached
Lower floor temperature
limit for cooling
(this function is active
when d04 = 1)
d16
d18
6°C
0
Simultaneously hold the buttons
for 3 seconds.
- Frost protection mode. Usually used in a longer period of absence
or during the holidays (available only in heating mode).
0
1
Heating system
Cooling system
Operating mode
HEATING / COOLING
3
4
Press any button to highlight the screen, then follow the steps below:
Choose mode
or buttons.
using
5
1
2
Error codes
Error code Description
Select the service parameter
using or buttons.
The parameter value
Err02
Err03
Err04
The maximum / minimum floor temperature has been exceeded
Temperature sensor is faulty
is set by
Press to confirm the changes.
or
.
Temperature sensor is shorted
Press to confirm the changes.
Choose the temperature mode
using or buttons.
Note: Heating / cooling mode can also be set using the service parameter
d18.
Note: To restore the thermostat’s factory settings, in step 2 set the PSuu
to 47 code, and confirm the selection with the button.
| General | Details |
|---|---|
| Name | SALUS Wired Thermostat Installation Guide |
| Make | SALUS |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.29 MB |
(1 votes, average: 5.00 out of 5)
Loading...
SALUS IT800 WIFI Smart Thermostat Installation Guide
SALUS 091FLRF Wireless Room Thermostat User Guide
SALUS Thermostat Sensor TS600 User Guide
SALUS Thermostat and Smart Plug Installation Guide
SALUS Programmable Wired Thermostat VS30W/VS30B Installation Guide
SALUS Wired Digital Thermostat – Non-programmable HTRS230 User Manual
SALUS RT520 Radiator Thermostat User Guide
SALUS RT310 Thermostat User Manual
SALUS Thermostat RT520 User Manual
SALUS TS600 Wireless Temperature Sensor Thermostat User Guide
LUXPRO PSD111+ Series Thermostat Instruction Manual
Danfoss VICUX40F Icon Dial 230V Room Thermostat Installation Guide
hansgrohe AXOR STARCK Concealed Thermostat with Shut Off Valve Instruction Manual
AuVerte C504 Ondur Elegant Temperature Control Thermostat Installation Guide
SMART TEMP SMT-131 Hotel Touchscreen Thermostat User Manual
HYSEN HY510 WiFi Heating Thermostat Instruction Manual
Honeywell Home RTH Series X2S Smart Thermostat Installation Guide
telkonet Aida Wireless Thermostat User Guide
beok TDR89 Wi-Fi Thermostat User Guide
Honeywell RTH8500 Wi-Fi Series Thermostat User Guide