×
- 1. Manual For Use And Maintenance (Triple Phase Digital Thermostat)
- 2. Manual For Use And Maintenance (Revision → Product Software → Technical Documentation → User Authorization → Modifications To The Apparatus)
- 3. Introduction (Disclaimer → Notes)
- 4. Precautions (Introduction To The Rdt-5)
- 5. Features (Indicator Leds)
- 6. Display (Abbreviations → Rdt-5 Abbreviations)
- 7. Using The Rdt-5 (Rdt-5 Keyboard → Cold Start → Software Version → Rdt-5 Configuration)
- 8. Cold Start (Software Version → Rdt-5 Configuration → Quick Start)
- 9. Reading The Main Screen (Displaying The Current Temperature → Configuring The Basic Settings)
- 10. Configuring The Stage Activation Temperature (Configuring The Temperature Curve)
- 11. Setting The Day (Setting The Target Temperature → Saving Values To Memory → Additional Details)
- 12. Installation (Mounting → Wiring → Configuring The Rs-485 Communication)
- 13. Electing Eating Or Ooling Unctions (Each Relay Must Be Set To Operate A Heater Or Cooler → To Set The Relay Function)
- 14. Cooling And Heating Jumpers (Wiring Between Rdt-5 And Fbu-27 Se)
- 15. Rdt-5 (Wiring Between Rdt-5 And Rts-2 → Powering The Rdt-5)
- 16. Caution (Alarm Trigger Conditions → Rdt-5 Wiring To Platinum Controllers)
- 17. Figure 11: Wiring The Backup Alarm Ports To The Platinum Digital Input Card
- 18. Latinum Ommunication (Rs-485 Communication → Rs-232 Communication → Rdt-5 Communication Card → Platinum Communication Card → Note → Caution)
- 19.
- 20. Caution (Configuring The Rs-485 Communication → Defining The 5v Status → Defining The Termination → Defining The Baud Rate)
- 21. Rdt-5 At Chain Endpoint (Rdt-5 In Mid Chain)
- 22. Specifications (Power Supply → Relays Outputs → Housing → Ambient Climate → Operating Temperature Range → Certification)
- 23. Appendix A: Setting The Temperature Curve In Legacy Software (To Configure The Temperature Curve: → Values Are Saved To Memory. → The Display Returns To The Main Screen. → Note After 60 Seconds Of Inactivity On The Keyboard, The Display Automatically Returns To The Main Screen.)
- 24. Warranty And Technical Assistance (Munters Products Are Designed And Built To Provide Reliable And Satisfactory Performance But Cannot Be Guaranteed Free Of Faults; Although They Are Reliable Products They Can Develop Unforeseeable Defects And The User Must Take This Into Account And Arrange Adequate Emergency Or Alarm Systems If Failure To Operate Could Cause Damage To The Articles For Which The Munters Plant Was Required: If This Is Not Done, The User Is Fully Responsible For The Damage Which They Could Suffer.)
×
Munters RDT-5 Triple Phase Digital Thermostat User Manual
Figure 4: RDT-5 Boards and Ports
ELECTING EATING OR OOLING UNCTIONS
5.2.1 S
H
C
F
Each relay must be set to operate a heater or cooler (Figure 5).
Figure 5: Jumpers Locations
To set the relay function:
On each relay, place the jumper over the required pins. Figure 6 displays two
examples.
•
© Munters AB, 2021
15
| General | Details |
|---|---|
| Name | Munters RDT-5 Triple Phase Digital Thermostat User Manual |
| Make | Munters |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.5 MB |


VIMAR 02970 Wheel Thermostat Instruction Manual

SIEMENS TH192 HC Heating-Cooling Room Thermostat Instruction Manual

sinope TH1500ZB Smart Double Pole Thermostat Installation Guide

SECURE ThermoPlus PRT1 Programmable Room Thermostat Instruction Manual

Danfoss RAS-D2 Radiator Thermostat Installation Guide

Commercial Electric HTSA15CWB Smart Thermostat User Guide

OUELLET OTL221 Single Pole Mechanical Thermostat Instructions

KETOTEK KT3200 Plug In Thermostat Day Night Temperature Controller Instruction Manual

UNDERFLOOR HEATING WORLD UWi5 Wi-Fi Digital Heating Thermostat Instruction Manual

autani 1000172-01 Wave Thermostat Installation Guide
Table of Contents
- 1. Manual For Use And Maintenance - Triple Phase Digital Thermo... →
- 2. Manual For Use And Maintenance - Revision →
- 3. Introduction - Disclaimer →
- 4. Precautions - Introduction To The Rdt-5 →
- 5. Features - Indicator Leds →
- 6. Display - Abbreviations →
- 7. Using The Rdt-5 - Rdt-5 Keyboard →
- 8. Cold Start - Software Version →
- 9. Reading The Main Screen - Displaying The Current Temperature →
- 10. Configuring The Stage Activation Temperature - Configuring T... →
- 11. Setting The Day - Setting The Target Temperature →
- 12. Installation - Mounting →
- 13. Electing Eating Or Ooling Unctions - Each Relay Must Be Set ... →
- 14. Cooling And Heating Jumpers - Wiring Between Rdt-5 And Fbu-2... →
- 15. Rdt-5 - Wiring Between Rdt-5 And Rts-2 →
- 16. Caution - Alarm Trigger Conditions →
- 17. Figure 11: Wiring The Backup Alarm Ports To The Platinum Dig... →
- 18. Latinum Ommunication - Rs-485 Communication →
- 19. Page 19 →
- 20. Caution - Configuring The Rs-485 Communication →
- 21. Rdt-5 At Chain Endpoint - Rdt-5 In Mid Chain →
- 22. Specifications - Power Supply →
- 23. Appendix A: Setting The Temperature Curve In Legacy Software... →
- 24. Warranty And Technical Assistance - Munters Products Are Des... →




























