SALUS AT10 Contact Thermostat User Manual

1

2

Montage  

AT10: For installation, press the thermostat firmly to the heat pipe and  

fix it with the supplied elastic band so that the thermostat is in direct  

contact with the pipe (remove any insulation at the installation spot  

before fixing the sensor). Excess elastic band can be trimmed.  

Contact thermostat / Capillary thermostat  

Model: AT10, AT10F  

AT10F: Fix the thermostat to a flat surface using screws. Then place the  

measuring element (capillary) in the measuring sleeve, e.g. located in  

the hot water tank.  

Changing temperature setpoint  

To set the temperature, pull the knob towards you to release it. Then  

turn the knob to the position which indicates the required temperature.  

To keep this setting, press the knob lightly in the inward direction until  

a click is heard.  

User manual  

Technical informations  

SALUS CONTROLS DISTRIBUTOR:  

QL CONTROLS Sp. z o.o., Sp. k.  

ul. Rolna 4,  

43-262 Kobielice,  

Poland  

Importer:  

SALUS Controls Plc  

Units 8-10 Northfield Business Park  

Forge Way, Parkgate, Rotherham  

S60 1SD, United Kingdom  

Power supply  

230V AC  

Max. load  

16 (4) A  

Output signal  

terminals 1/C/2 (NO/COM/NC)  

30 – 90 °C  

Temperature adjustment range  

www.salus-controls.eu  

SALUS Controls is a member of the Computime Group.  

Inaccordancewiththeproductdevelopmentpolicy,SALUSControlsplcreservestherighttochange  

specifications, design, and materials used in production, presented in this manual, without prior  

notice.  

105 x 50 x 45  

AT10F: length of the capillary:  

1200, Ø of the capillary: 7  

Dimension [mm]  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	SALUS AT10 Contact Thermostat User Manual
Make	SALUS
Language	English
Filetype	PDF (Download)
File size	0.07 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• SALUS

SALUS AT10 Contact Thermostat User Manual Overview

Summary of Contents

• Page 1: Montage For installation, press the thermostat firmly to the heat pipe and fix it with the supplied elastic band so that the thermostat is in direct contact with the pipe. Excess elastic band can be trimmed. Fix the thermostat to a flat surface using screws. To set the temperature, pull the knob towards you to release it. Then turn the knob to the position which indicates the required temperature. To keep this setting, press the knob lightly in the inward direction until a click is heard. Power supply: 230V AC. Max. load: 16 (4) A. Temperature adjustment range: 30 – 90 °C. In accordance with the product development policy, specifications, design, and materials used in production may change without prior notice.
• Page 2: Introduction The AT10 contact thermostat / AT10F capillary thermostat is a mechanical thermostat that can be easily installed on the surface of a pipe or by placing the capillary in a sleeve. It allows for the control of temperature in hot water or central heating systems and can switch connected devices on or off based on the measured temperature. The product is compliant with the Low Voltage Directive LVD 2014/35/EU and RoHS Directive 2011/65/EU. Installation must be carried out by a qualified person, in accordance with national and EU regulations. Use the device as intended and do not allow it to get wet; it is for indoor use only. Underfloor heating protection against overheating is provided by opening the C-1 terminals if the temperature exceeds the setpoint. Filling the hot water tank occurs if the temperature drops below the set value, with the C-1 terminals closing. Description of electrical connections includes details on terminal functions and maximum ratings.