VIVE TP-S-955WH Programmable Thermostat Instruction Manual
Installation Tips
Installation Tips
Base Module - Basement Location
When performing an attic installation, instead of placing the base
module in the attic, locate the closet nearest to the air conditioning
unit. Then mount the base module high on the wall inside the closet or
on the ceiling of the closet. This location will insure the base module is
below the 150°F maximum ambient temperature specification.
Wireless Range
Range between the thermostat and the base module is up to 100 feet
with no obstructions and approximately 50 feet in standard residential
construction. To extend the range try replacing the base unit higher if
in a basement or further away from large metal objects.
Better
Good
Attic
Better
No
Living space
Good
Living space
closet
Installation Tips
Installation Tips
Do not install the base module in locations:
Do not install the base module in locations:
• That are behind a chimney
• Where temperature could exceed 150°F
• Where rain or snow or extreme hot or cold is possible
• That are behind a chimney
• Where temperature could exceed 150°F
• Where rain or snow or extreme hot or cold is possible
Note: This base module is NOT weatherproof.
Note: This base module is NOT weatherproof.
8
7
Wireless Communication Tips
Private Label Badge
About The Badge
Pro1 Base Module
for use with T955WH
All of our thermostats use the same universal magnetic badge. Visit the
company website to learn more about our free private label program.
H
Temperature
D
Y1
Y2
W1/E
W2
Clean
Display
Humidity
UPSTAIRS
G
UPS
O
Clean
B
Set Time
Next Zone
Follow these steps for a simple wireless communication setup.
Locate all components in
area near equipment.
l
m
q
fP
l
k
=
Wire base module with 8ft
pigtail and temporarily mount.
Use the bevel on lower ridge
If you are not able to establish
communication, this will allow
you to relocate the module to
an area with less obstruction,
without having to rewire.
l
m
q
fO l
k
=
Install batteries in all devices
you wish to use.
Thermostat, indoor/outdoor sensors.
l
m
q
fN l
k
=
Magnet in door
A. Press the menu button
on thermostat
Gently slide a screwdriver into the
B. Press & hold tech set up button
C. Configure the set up for
your application
bottom edge of the badge. Gently turn
the screwdriver counter clockwise. The
badge is held on by a magnet in the well
of the battery door. The badge should pry
off easily. DO NOT USE FORCE.
D. Establish communication between devices
Install thermostat in final location.
Note: You must hardwire the thermostat when using remotes.
Turn on fan from thermostat to ensure communication.
Once communication is established, permanently mount module.
Troubleshooting
If there is no communication between the thermostat and base
module devices that are less than 50ft. apart, utilize an 8ft. pigtail to
relocate and reduce interference. If there is not communication and
devices are over 50ft. apart, add a W150W - Wireless Repeater.
12
11
| General | Details |
|---|---|
| Name | VIVE TP-S-955WH Programmable Thermostat Instruction Manual |
| Make | Vive |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.67 MB |
(1 votes, average: 5.00 out of 5)
Loading...
VIVE TP-N-751 Programmable Thermostat Installation Guide
VIVE TP-S-855C Digital Programmable Thermostat Instruction Manual
THE HEATING COMPANY Slim and Compact WiFi Thermostat User Manual
GENERAL LIFE MITRA 250S RF Digital Room Thermostat User Manual
Carrier 53DFS250-SL Programmable Digital Thermostat Owner’s Manual
Wagner AL8010F Refrigeration or Heating Digital Thermostat User Manual
sinope TH1500ZB Smart Double Pole Thermostat Installation Guide
Wiser CCTFR6400 Room Thermostat User Manual
Sygonix 2735095 Wireless Indoor Thermostat Instruction Manual
SALUS BTR230 Room Thermostat User Guide
Aprilaire S86N MU Multi Stage Universal Thermostat Instruction Manual
EPH CONTROLS RFRA RF Room Thermostat Installation Guide