Home > PRO1 > PRO1 T751i Thermostat Installation Guide

PRO1 T751i Thermostat Installation Guide

Product Installation Guide  
Installation Tips  
Wall Installation  
The thermostat should be installed approximately 4 to 5 feet above the floor.  
Select an area with average temperature and good air circulation. Pick an  
installation location that is easy for the user to access. The temperature of the  
location should be representative of the building.  
T751i  
Pro1 Technologies  
P.O. Box 3377  
Springfield, MO 65808-3377  
Do not install  
thermostat in locations:  
Toll Free : 888-776-1427  
Hours of Operation: M-F 9AM - 6PM EST  
• Close to hot or cold air ducts  
• That are in direct sunlight  
• With an outside wall behind the  
thermostat  
• In areas that do not require  
conditioning  
• Where there are dead spots or  
drafts (in corners or behind doors)  
• Where there might be concealed  
chimneys or pipes  
PM-T751i-IM-2403  
*PM-T751i-IM-2403*  
Power Type  
Thermostat Application Guide  
Hardwire (24V Common Wire)  
Description  
Gas or Oil Heat  
Yes  
Yes  
Yes  
Yes  
A trained, experienced  
technician must install this product.  
Electric Furnace  
Heat Pump (No Aux. or Emergency Heat)  
Heat Pump (With Aux. or Emergency Heat)  
Multi-Stage Systems  
Carefully read these  
instructions. You could damage this  
product or cause a  
hazardous condition if you fail to  
follow these instructions.  
Yes  
Yes  
Yes  
Heat Only Systems  
Cool Only Systems  
No  
Millivolt  
Removing The Private Label Badge  
Una version en espanol de este  
manual se puede descargar en la  
pagina web de la compania.  
Gently slide a screwdriver into the  
bottom edge of the badge. Gently  
turn the screwdriver counter  
clockwise. The badge is held on by  
a magnet in the well of the battery  
door. The badge should pry off easily.  
Table of Contents  
Page  
Installation Tips  
Thermostat Quick Reference  
Subbase Installation  
Wiring  
Technician Setup  
WIFI Setup  
Specifications  
2
3
4
5-7  
8-12  
13  
14  
WIFI  
Frequency Range............2.4 Ghz ISM radio band  
WIFI Module...............................Supporting 802.11  
B/G/N Standards  
Use the bevel on lower ridge  
DO NOT USE FORCE.  
All of our thermostats use the same  
universal magnetic badge. Visit the  
company website to learn more about  
our free private label program.  
Magnet in door  
U.S. Registered Trademark. Patents pending  
Copyright 2024 All Rights Reserved.  
1
2
Rev. 2403  
Thermostat Quick Reference  
Subbase Installation  
Horizontal Mount  
For horizontal mount put one  
screw on the left and one screw  
on the right.  
LCD Display  
Glow in the dark light button  
Fan Button  
Vertical Mount  
For vertical mount put one  
screw on the top and one screw  
on the bottom.  
System Button  
Temperature Setpoint Buttons  
Private Label Badge  
Electrical Hazard  
Failure to disconnect the power before  
beginning to install this product can cause  
electrical shock or equipment damage.  
Set At  
COOL ON  
HEAT ON  
FAN ON  
Mercury Notice  
NOTE: To ensure a solid fit between  
the thermostat and subbase:  
1. Mount subbase on a flat wall.  
2. Use provided screws.  
All of our products are mercury free.  
However, if the product you are replacing  
contains mercury, dispose of it properly.  
Your local waste management authority  
can give you instructions on recycling and  
proper disposal.  
3. Ensure drywall anchors are flush with wall.  
4. Push wires into wall.  
Em.Heat  
STAGES AutoCool  
Mount Thermostat  
Indicates the current room temperature  
1
2
3
Setpoint: Displays the selected setpoint temperature.  
System Operation Indicators: The COOL ON, HEAT ON or FAN ON will display  
when the COOL, HEAT, or FAN is on. The compressor delay feature is active if these  
are flashing.  
Align the 4 tabs on the subbase  
with corresponding slots on the  
WIFI Indicator: Shown when connected to WiFi.  
back of the thermostat, then push  
gently until the thermostat snaps  
in place.  
Globe: Globe is displayed if an energy efficient setpoint temperature has been  
selected.  
Fan: Indicates the current fan setting.  
Stages: 1 will appear in the display when the first stage of heat or cool is on.  
+2 will appear for the second stage of heat.  
7
System: Indicates current system mode setting.  
4
GeneralDetails
NamePRO1 T751i Thermostat Installation Guide
MakePRO1
LanguageEnglish
FiletypePDF (Download)
File size0.3 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...
PRO1 T731W Wireless PTAC Non-Programmable Thermostat Installation Guide
PRO1 T731W Wireless PTAC Non-Programmable Thermostat Installation Guide
PRO1 T805 Non Programmable Thermostat Instruction Manual
PRO1 T805 Non Programmable Thermostat Instruction Manual
PRO1 T701 Digital Non Programmable Thermostat Instruction Manual
PRO1 T701 Digital Non Programmable Thermostat Instruction Manual
PRO1 IAQ T721i Digital WIFI Programmable Thermostat User Manual
PRO1 IAQ T721i Digital WIFI Programmable Thermostat User Manual
PRO1 R250W Wireless System Thermostat Owner’s Manual
PRO1 R250W Wireless System Thermostat Owner’s Manual
PRO1 T725 Thermostat User Guide
PRO1 T725 Thermostat User Guide
PRO1 T755 Heat 2 Cool Dual Fuel Thermostat User Manual
PRO1 T755 Heat 2 Cool Dual Fuel Thermostat User Manual
PRO1 T771 Programmable Electronic Thermostat Instructions
PRO1 T771 Programmable Electronic Thermostat Instructions

PRO1 T751i Thermostat Installation Guide