Honeywell ATC928 Evohome Connected Multi Zone Room Thermostat Installation Guide
24
Step 3: Power up and bind devices
Underfloor Heating Controller (HCE80 or HCC80)
Power up and bind an Underfloor
evohome
Controller
Heating Controller (HCE80 or HCC80)
If you are NOT
following GUIDED
If you want to control the zone temperature with your
evohome Controller (the evohome Controller needs
to be located in that zone) press YES, otherwise
press NO and bind a sensor – either Digital Room
Thermostat (DTS92), Single Zone Thermostat (Y87RF),
or Room Temperature Sensor (HCW82/HCF82)
CONFIGURATION
follow these steps
on your evohome
Controller display once
the underfloor heating
controller and sensors
have been fitted:
1. On the evohome
Controller press and
hold “Settings” for
3 seconds
To bind the Digital Room Thermostat (DTS92)
1
Press and hold the power button
for 2
seconds to put the unit into standby
2. Press the green tick
2
Press the up and down arrows together for
three seconds – it should say INst
3. Press ADD ZONE
4. Type a name for the
new zone and press
the green tick
3
4
5
6
7
Press the down arrow – it should say COnt
Press the up arrow three times – it should say CLr
5. Press UNDERFLOOR
HEATING
Press the
Press the up arrow – it should say COnt
Press the once to send the binding
once to clear any previous binding data
6. You need to install
a sensor (HCW82,
HCF82, DTS92) in
each zone controlled
by the underfloor
heating controller
and bind it to the
evohome Controller.
signal to the evohome Controller
8
You should receive a SUCCESS message on the
evohome Controller (if not go back and re-bind)
You need to repeat this
process for every zone
that uses underfloor
heating.
To bind the Single Zone Thermostat (Y87RF)
1
Press and hold on the left touch zone (just below
and to the left of the display) for approximately
10 seconds until a flashing 'Bo' is displayed
2
Turn the dial clockwise until a flashing 'Co' is displayed
3
Press the left touch zone once to send the
binding signal to the evohome Controller
!
4
You should receive a SUCCESS message on the
Make sure the zone
you’re adding on the
evohome Controller
corresponds to the
correct underfloor
heating zone.
evohome Controller (if not go back and re-bind)
| General | Details |
|---|---|
| Name | Honeywell ATC928 Evohome Connected Multi Zone Room Thermostat Installation Guide |
| Make | Honeywell |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.53 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Honeywell T6 Pro Programmable Thermostat User Manual
Honeywell D1-528 Direct Thermostat Installation Guide
Honeywell FocusPRO P200 Programmable Thermostat User Guide
Honeywell RCHT8610WF Series Smart Thermostat Installation Guide
Honeywell T9 Smart Thermostat Installation Guide
Honeywell TH2320WF4011 FocusPRO Smart S200 Series Thermostat User Guide
Honeywell TL116A Thermostat Installation Guide
T10 Pro Smart Thermostat with Redlink Room Sensor
Honeywell TH6320WF2003 Lyric T6 Pro Wi-Fi Programmable Thermostat User Guide
Honeywell RTH9580 Wi-Fi Color Touchscreen Programmable Thermostat User Guide
Uponor ETN4 Ecoflex Supra Standard Thermostat Instruction Manual
PERRY TE541 Digital Thermostat User Manual
Thermostats BHT-8000RF Wireless Thermostat User Manual
GENERAL SOLARA 330S SMART Smart Room Thermostat User Manual
Honeywell CT31 Low Voltage Thermostat Owner’s Manual
Roth Basicline Room Thermostat Instructions
CYDATA CY917B Daisy Wi-Fi Thermostat User Guide
bryant ecobee3 Lite Smart Thermostat User Guide
GENERAL LIFE NORA 270S Digital Room Thermostat User Manual
DEVIreg 330 Electronic Thermostat Installation Guide