FURRION FACW10ESSA-BL Standard Single Zone Wall Thermostat User Guide

1

2

This quick start guide will help you install and use the  

device properly. For further support please visit  

www.furrion.com/support.  

1. Mount the thermostat on an interior wall, approximately  

5 ft. (1.5m) above the floor. Install in a location with good  

air circulation and avoid damp areas.  

2. Avoid to install the thermostat in areas that are  

exposed to temperature variances, such as direct  

sunlight, near windows and doors, above or below  

supply vents. Do not install the thermostat in locations  

near heat sources like televisions, lamps, or fireplaces.  

PRODUCT OVERVIEW  

STANDARD SINGLE ZONE  

WALL THERMOSTAT  

Room Temperature or  

Error Code  

Operation Mode  

Wiring and Mounting the Thermostat  

MODEL: FACW10ESSA-BL  

Fan Speed  

Press to change  

the fan speed  

1. Rotate the thermostat cover counterclockwise and pull  

out the base plate.  

Press to increase the  

temperature set-point  

Press to decrease  

temperature set-point  

2. Use the base plate as a template and drill a hole on  

the vehicle wall. Extend the four wire cables from the  

cutout area. Refer to the cable tag label for each cable  

definition.  

Press once to turn on.  

Press repeatedly to  

select mode  

QUICK START GUIDE  

3. Mount the thermostat base on the wall using screws  

included with the thermostat.  

NOTE: Make sure the base is not covering the hole and  

squeezing the thermostat cables. Take care in case of  

damaging the temperature sensor.  

WHAT’S IN THE  

B

OX  

Warranty Manual  

Quick Start Guide  

4. Connect the cables to thermostat.  

5. Replace the thermostat to the base and rotate  

clockwise until it snaps into place.  

2

1

QSG x 1  

Warranty Manual x 1  

Thermostat x 1  

Thermostat Cables  

NOTE: Product design and packaging may change without  

notice.  

34  

34  

INSTALLATION  

Thermostat  

cables  

Thermostat Cables  

WARNING: Risk of electric shock. Always verify that the  

electrical power to the circuit has been disconnected  

before performing the installation procedures.  

5

Thermostat Location  

This thermostat is a regulating device which senses the  

room real-time temperature and performs actions to  

maintain the temperature near a desired set-point. For  

accurate temperature control, the following considerations  

should be taken into account:  

For further support and to download the air  

conditioner user manual please scan the QR  

code or visit: https://furrion.com/pages/  

downloads-climate  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	FURRION FACW10ESSA-BL Standard Single Zone Wall Thermostat User Guide
Make	FURRION
Language	English
Filetype	PDF (Download)
File size	0.21 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• FURRION

FURRION FACW10ESSA-BL Standard Single Zone Wall Thermostat User Guide Overview

Summary of Contents

• Page 1: This quick start guide will help you install and use the device properly. Mount the thermostat on an interior wall, approximately 5 ft. (1.5m) above the floor. Avoid installing the thermostat in areas that are exposed to temperature variances, such as direct sunlight, near windows and doors, above or below supply vents. Do not install the thermostat in locations near heat sources like televisions, lamps, or fireplaces. Connect the cables to the thermostat. Replace the thermostat to the base and rotate clockwise until it snaps into place. Always verify that the electrical power to the circuit has been disconnected before performing the installation procedures. This thermostat is a regulating device which senses the room real-time temperature and performs actions to maintain the temperature near a desired set-point. For accurate temperature control, certain considerations should be taken into account. Product design and packaging may change without notice.
• Page 2: DIP switch settings should be referenced in the air conditioner instruction manual. Only activate the heat mode for the zone controller intended to operate the heating function. The Furrion wall thermostat has factory default settings that can be adjusted for comfort. Temperature set-point ranges from 60°F to 86°F (16°C to 30°C). To turn on the thermostat, press and hold the button for 3 seconds. The available fan settings vary by mode: Low/High/Auto for Cool, Low/High/Auto/Off for Heat, and Low/High for Fan. Press both buttons for 3 seconds to toggle the temperature format between Centigrade and Fahrenheit. In Auto mode, the fan operates automatically based on temperature differences. Error codes will display on the LCD for various faults detected by the system. The heat mode can be disabled if both the furnace and heatstrip are off.