Home > Greystone > GREYSTONE TLGLF24X01 Glass Low Limit Thermostat Instruction Manual

GREYSTONE TLGLF24X01 Glass Low Limit Thermostat Instruction Manual

2

Glass Low Limit Thermostat

TLGL Series - Installation Instructions

INTRODUCTION

The low limit glass thermostat incorporates

precision thermistor

temperature sensor and provides a Form C relay output (NO/NC) with an

adjustable setpoint. The sensor is encapsulated in a 31.75mm L x 9.525mm W

x 9.525mm H (1.25" x 0.375" x 0.375") Aluminum probe. Standard wire length

is 1.5 m (5'). All probes are constructed to provide excellent heat transfer, fast

response and are potted to resist moisture penetration.

BEFORE INSTALLATION

Read these instructions carefully before installing and commissioning

the temperature sensor. Failure to follow these instructions may result in

product damage. Do not use in an explosive or hazardous environment,

with combustible or ﬂammable gases, as a safety or emergency stop

device or in any other application where failure of the product could

result in personal injury. Do not exceed the device ratings.

MOUNTING

The glass thermostat installs directly onto any window where the enclosure can be mounted nearby. Select a suitable location on an exterior

window where both the probe and the enclosure can be mounted. On one side of the probe apply epoxy compound and press ﬁrmly against

the glass. See Figure 1. Use whatever means available (electrical tape will do) to secure the probe to the window while the epoxy sets.

Unroll the sensing cable probe, being careful not to kink the wire. Secure the enclosure to the wall with two #10 x 25 mm (1”) self tapping screws

(not provided). Tighten screws until the enclosure is tight against the wall and ensure that there is no movement of the enclosure as shown in

Figure 1.

The enclosure has a hinged cover with a latch. Open the cover by pulling slightly on the latch on the right side of the enclosure, at the same time

pulling on the cover, as illustrated in Figure 2.

Figure 1

A 1/2" NPT threaded connection hole is provided in the bottom of the enclosure. Screw

the EMT connector or cable gland connector in until tight. See Figure 3. It is recommended

that weatherproof conduit or cable gland ﬁttings be used. An optional 1/2" NPT to M16

thread adapter and cable gland ﬁtting is available.

Make wire connections as per the“Wiring”illustrations on Page 2.

Swing door closed until securely latched. For added security, two screws are provided

that may be installed in the integrated screw tabs. See Figure 4.

Figure 2

Figure 3

Figure 4

Thread adapter and

cable gland ﬁtting

EMT Connector

Page 1

IN-GE-TLGLXXX-003

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	GREYSTONE TLGLF24X01 Glass Low Limit Thermostat Instruction Manual
Make	Greystone
Language	English
Filetype	PDF (Download)
File size	0.2 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Comments are closed.

Greystone Instructions & User Manuals

GREYSTONE TLDF Series Flexible Cable Duct Average Low Limit Thermostat Instruction Manual

GREYSTONE TLOSF24X01 TLOS Series Outside Low Limit Thermostat Instruction Manual

GREYSTONE TLDCB24J01 Flexible Copper Duct Average Low Limit Thermostat Instruction Manual

GREYSTONE TLFLF24X01 Flying Lead Low Limit Thermostat Instruction Manual

Get the free PDF manual for the GREYSTONE TLGLF24X01 Glass Low Limit Thermostat Instruction Manual and access setup steps, usage instructions, and troubleshooting tips. 👉 View online or download now to keep your thermostat running smoothly!

Greystone TLGLF24X01 Manual: Questions and Answers

Greystone TLGLF24X01 specifications

Power supply	12 to 28 Vac/dc
Operating temperature	-10 to 50°C (14 to 122°F),53.7 mm
Power consumption	50 mA max

Full specifications, page 2

What is the adjustable setpoint range for Greystone TLGLF24X01?

-4 to 10°C (25 to 50°F). Instruction Manual, p. 2

What do the PWR, COM, and NO/COM/NC terminals do on Greystone TLGLF24X01?

PWR receives DC positive or AC hot; COM is the supply common; NO/COM/NC carries relay output.

Terminal	Function
PWR	DC positive or AC voltage hot side
COM	Supply common
NO/COM/NC	Relay output contacts

Instruction Manual, p. 2

How do I install Greystone TLGLF24X01 on a window?

Mount the probe and enclosure to an exterior window, secure the probe with epoxy, and fasten the enclosure with two screws.

Apply epoxy to one side of the probe and press firmly against the glass
Secure the probe with electrical tape while epoxy sets
Mount the enclosure to the wall with two #10 x 25 mm self-tapping screws
Tighten screws until enclosure is tight and has no movement Instruction Manual, p. 1