Futurehome Co020, Co021 Smart Thermostat PR Owner’s Manual

1

Description of screen indicators  

a.  

b.  

ZigBee icon. The ZigBee icon will flash when the thermostat  

searches for networks andlights up when connected.  

Time. This is set automatically after a short time  

when connected to the Futurehome Smarthub.  

c.  

Home and Away mode.  

Heating on / off indicator. If the thermostat heats the floor,  

the lines will move to the right.If maximum guard is used  

the lines flash if the temperature limit is exceeded.  

d.  

e. Indicator flashes when open window is detected.  

f. Manual / Auto indicator.  

g. Indicates that the temperature is set.  

h. Indicator for active child lock / button lock.  

Futurehome Smart Termostart PR  

User Manual - EN  

On/Off button  

Inc. temp  

Lower temp  

Mode button  

Zigbee pairing  

Functions  

To control the thermostat remotely it must be added to a ZigBee gateway  

Button  

Short press  

Long press  

1 . Start the process of adding new devices to your ZigBee gateway  

and follow the instructions.  

Confirm/go back  

Temperature increase  

Temperature decrease  

Turn ON/OFF  

Enter menu  

2 . To put the thermostat in pairing mode: Long press '-' until the  

ZigBee icon flashes.  

3 . Continue the process of adding new devices to the app.  

Start ZigBee pairing  

Change between home  

and away mode  

Display date in MM/DD  

format  

Advanced settings  

Long press ‘  

Long press ‘  

’ and‘  

’ and‘  

’ : Open advanced settings  

’ : Lock/Unlock  

When the thermostat is on, press and hold ‘ + ’ and ‘ - ’  

(5s) simultaneously to open advanced settings.  

Max guard function:  

1 . Sensor type  

Menu 1 / 02 Max guard. Floor sensor must be installed. The thermostat will  

regulate according to the room sensor, but interrupt heating if the floor  

sensor exceeds the maximum guard temperature. Standard is 27°C. This  

setting can be changed under Menu 3.  

00: Air sensor / Internal 01: Floor sensor / External  

02: Max guard / regulator on  

air temperature and limiter with floor sensor  

2 . Floor sensor type / External:  

There is also a maximum guard when the thermostat is set to floor sensor.  

The thermostat regulates according to the floor sensor, but will interrupt  

heating if the floor sensor exceeds the maximum guard temperature.  

Standard is 27°C. This setting can be changed under Menu 3.  

0: 10 kOhm | 1: 12 kOhm | 2: 15 kOhm | 3: 47 kOhm  

3 . Max Guarding Temperature：This must be set in the thermostat.  

20-95 ° C, Standard is 27 ° C, '-' No limit.  

4 . Turn: 1-9 ° C, Standard is 2 ° C  

To control the thermostat remotely it must be added to a ZigBee gateway  

5 . Calibration: -9 to + 9 ° C, Standard is 0 ° C  

6 . Highest set point: 35-90 ° C, Standard is 35 °C  

7 . Lowest setpoint: 0-30 ° C, Standard is 5 °C  

8 . Home mode setpoint: The standard is 22 ° C  

9 . Setpoint for away mode: The default is 15 ° C  

10. Brightness in sleep mode: 1-10, default is 1  

11. Open window detection: 0 = Disabled / 1 = Active  

1 . Start the process of adding new devices to your ZigBee gateway and  

follow the instructions.  

2 . To put the thermostat in pairing mode: Long press ‘  

’ until the  

ZigBee icon flashes  

3 .  

Continue the process of adding new devices to the app.  

Electrical data  

Power: 230 V / 50 Hz  

Circuit breaker: Max 16 A  

Maximum load: 3600 W  

1-pole electronic relay  

12. Restart the system:  

Press + or - to change '-' to '==' and waitfor 5s  

13. Reset to factory settings  

Press + or - to change '-' to '==' and waitfor 5s  

Internal power supply with galvanic isloation  

Do not use self-regulating heating cable  

Do not use for contactor control  

You can change settings with ‘ + ’ or ‘ - ’  

Press ‘ ’ to select the settings and proceed.  

Futurehome AS  

P.O Box 72, 0801 Oslo, Norway  

To save the changes and exit advanced settings,  

press ‘ ’ .  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Futurehome Co020, Co021 Smart Thermostat PR Owner’s Manual
Make	Futurehome
Language	English
Filetype	PDF (Download)
File size	0.14 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• Futurehome

Futurehome Co020, Co021 Smart Thermostat PR Owner’s Manual Overview

Summary of Contents

• Page 1: Description of screen indicators ZigBee icon will flash when the thermostat searches for networks and lights up when connected. Time is set automatically after a short time when connected to the Futurehome Smarthub. Heating on/off indicator shows if the thermostat heats the floor. Indicator flashes when an open window is detected. Manual/Auto indicator is present. Indicates that the temperature is set. Indicator for active child lock/button lock. To control the thermostat remotely, it must be added to a ZigBee gateway. Max guard function regulates according to the room sensor but interrupts heating if the floor sensor exceeds the maximum guard temperature. Electrical data includes power specifications and maximum load details.