COPELAND P-N 810-1600 Programmable Touchscreen Thermostat User Guide
IMPORTANT! If at least one of those parameters has been
changed, the thermostat will reboot: Thermostat system
configuration, number of Heating stages or number of
Cooling stages.
System Revision Display
The fifth and last configuration menu provides the current
system revision number. This number is shown with three
digits. Note that there is no decimal after the first digit, but the
revision number contains a decimal. For example, revision
number 100 on the display = 1.00. The software revision will
be updated for the latest official release, and will likely be
higher than 1.00. Touch the letters “CA” to cancel any
previous changes and go back to the normal display without
saving. Press the check icon to terminate the configuration
menus.
Prior to device restart, the display will show “- -” to indicate
that the device is about to reboot. When the device is
rebooting, the display will turn off for approximately a few
seconds until reboot operation has completed.
Figure 19 - Thermostat Display Before Reboot
Figure 18 - System Revision Display
E2
New Installation and Uploading of Touch_TStat Description File to E2
The Programmable Touchscreen Thermostat (P/N 810-1600) requires adding a description file (P/N 527-0729) to E2.
Contact Customer Service to obtain this information: ColdChain.CustomerService@copeland.com
NOTE: Ultrasite32
Software must be installed to perform a description file upload.
1. Connect to E2 using UltraSite32 (refer to the UltraSite32 Manual P/N 026-1002).
2. Launch the UltraSite program and log in.
3. Double-click to UltraSite to view Directory Level and Site Level.
4. Right-click on Site Level and click Connect.
5. Double-click on Site Level and locate the E2 Unit where the Touch T-Stat.dsc will be installed.
6. Right-click on the unit and select Upload Description File.
7. Click Browse and select the appropriate description (*.dsc) file for Touch T-Stat.dsc from the computer and click Open.
8. Click Upload. A window will display that the description file was successfully imported. Click OK. The description (*dsc) file
should appear in the list.
9. Once completed, disconnect from the E2 and reboot the E2 controller - either manually with the toggle switch or remotely
through Terminal Mode.
NOTE: DO NOT omit the step of rebooting the controller.
026-4850 R2
6
©2024 Copeland LP.
| General | Details |
|---|---|
| Name | COPELAND P-N 810-1600 Programmable Touchscreen Thermostat User Guide |
| Make | Copeland |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.3 MB |
(1 votes, average: 5.00 out of 5)
Loading...
COPELAND 1F95G-1235GC Humidity Universal Thermostat Instruction Manual
COPELAND ST55 Sensi Smart Thermostat Instruction Manual
COPELAND 1F76U-22WFB Series Sensi Lite Smart Thermostat Installation Guide
COPELAND 026-1739 Programmable Touchscreen Thermostat User Manual
COPELAND 1F86-0244 Blue 2 Inch Single Stage Thermostat Instruction Manual
BAXI uSense 2 Wired Smart Thermostat Gateway Installation Guide
EMERSON 1F76U-22WFB Series Sensi Lite Smart Thermostat Installation Guide
THORGEON 18007 Digital Plug In Thermostat Instructions
expert4house BHT-8000 Heating Thermostat User Guide
EPH CONTROLS eTRV-HW Smart Hot Water Thermostat Instruction Manual
GENERAL LIFE ARUNA 302S Smart Room Thermostat User Manual
Honeywell CMR707A1049 Programmable Room Thermostat User Guide
ENSTO ECO16BTD Floor Heating Thermostat User Guide
Infracomfort HY312W Wifi Digital Thermostat User Manual
dahua TRV1 Smart Radiator Thermostat Owner’s Manual