75F HyperStat All In one Commercial Thermostat User Manual

1

2

3

4

SPEC SHEET  

75F^® HyperStat  

All-in-one commercial thermostat and humidistat with  

8 on-board sensors for superior IAQ management  

and localized temperature control  

⎯Occupancy, temperature, light, humidity, sound, CO₂ and  

optional VOC and particulate matter (PM2.5 and PM10)  

⎯TFT LCD display with touch slider and user buttons  

⎯(6) Onboard relays  

⎯(3) Analog outputs  

⎯(2) Thermistor inputs  

⎯(2) Analog inputs  

1800 121 4575 | enquiries@75f.io  

|

www.75f.io  

HyperStat_0624  

1

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	75F HyperStat All In one Commercial Thermostat User Manual
Make	75F
Language	English
Filetype	PDF (Download)
File size	0.16 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• 75F
• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS

75F HyperStat All In one Commercial Thermostat User Manual Overview

Summary of Contents

• Page 1: All-in-one commercial thermostat and humidistat with 8 on-board sensors for superior IAQ management and localized temperature control. Occupancy, temperature, light, humidity, sound, CO2 and optional VOC and particulate matter (PM2.5 and PM10). TFT LCD display with touch slider and user buttons. (6) Onboard relays. (3) Analog outputs. (2) Thermistor inputs. (2) Analog inputs.
• Page 2: Give your occupants the power of IAQ management and localized temperature control with 75F’s HyperStat, an all-in-one thermostat and humidistat thoughtfully crafted to support healthy, comfortable spaces. The HyperStat works out of the box with the 75F intelligent building solution. The 75F HyperStat is an all-in-one IAQ sensing station, thermostat and humidistat. Occupants can make temperature adjustments within predefined limits from a touch slider, TFT LCD screen, or buttons. This device supports the WELL Building standard for healthy buildings and tracks occupancy, temperature, dedicated CO2, humidity, light, sound, and optional VOC and particulate matter measurements every 60 seconds. Built-in sequences for occupancy detection mean your HyperStat prioritizes health and comfort when it matters most and saves valuable energy when spaces are empty. Facility directors have real-time access to sensor data and remote control over building parameters through the HyperStat’s integration with Facilisight. Auto Away and Auto Forced Occupied settings override building schedules to save energy with setback modes in unoccupied spaces. Pre-loaded equipment profiles allow for interfacing to a wide variety of staged and fully modulating equipment. The sleek, contemporary design will look right at home in any space.
• Page 3: Dimensions: 6.5” x 4.5” x 1.18” (165.5mm x 115mm x 30mm) Operating range: 32°F to 122°F (0°C to 50°C) Typical accuracy: +/- 1°F or 0.2°C Power: 24V AC/DC (+/-15%); nominal power consumption 1.0W, maximum consumption 2.5W Humidity operating range: 20 to 85% noncondensing; typical accuracy of +/- 2% RH Bluetooth: BLE4.1; used during commissioning Dedicated CO2 sensor range: 0-40,000 ppm; accuracy +/-30ppm over range of 400-10,000ppm Wired communication: 4 wire RS-485 interface and 3 wire connector for low-power sensor bus Occupancy detection: Passive Infra Red (PIR) with detection range of 4m and 30-degree angle VOC sensor: TVOC range 0-60,000 ppb; typical accuracy 15% of measured value
• Page 4: I/O (2) 10k type-2 thermistor inputs with 2% accuracy (2) 0-10V analog voltage inputs with 2% detection accuracy (6) 24V dc/1A relays (3) 0-10V/4-20mA analog outputs with a maximum load of 20mA per channel