VIMAR 30810.G View Wireless Connected Dial Thermostat Instruction Manual

1

2

3

SMART HOME VIEW WIRELESS  

30810.x - 02973 Connected dial thermostat  

TWO OPERATING MODES (ALTERNATIVE)  

Stand alone •  

A

B

Download the View Wireless  

will be using for configuration.  

App from the stores onto the tablet/smartphone you  

C

When the device is powered for the first configuration, we recommend you search for any  

new firmware and perform the update.  

Depending on the mode you select, you will need:  

1

2

Stand alone  

Gateway  

art. 30807.x-20597-19597-16497-14597  

View App  

Nothing else  

• Short press = degrees Celsius/Fahrenheit selection  

for management via smartphone/tablet  

• Long press (5 s) = the thermostat enters the configuration phase (bt)  

• Prolonged press (30 s) within the first 5 min of powering = device reset (rst)  

Amazon Alexa, Google Assistant, Siri and Homekit voice  

assistants for possible voice operation  

Display brightness and RGB LED in standby setting  

• 1st press = current brightness display  

Create your Installer account on MyVimar (on-line).  

• Subsequent presses = cyclic display of available brightness values L-3 (high), L-2  

(medium), L-1 (low) and L-0 (off).  

STAND ALONE CONFIGURATION  

1. Wire all the thermostats.  

Display  

2. Start the View Wireless App and log in with the credentials you just created.  

3. Create the system and the environments.  

4. Associate all the thermostats with the environments.  

To associate the thermostat:  

• bt = devices in Bluetooth configuration  

• off = thermostat off; on = thermostat on  

• °C = degrees Celsius; °F = degrees Fahrenheit  

• L-0, L-1, L-2, L-3 = brightness in standby (from the lowest to the highest)  

• H = heating; C = air conditioning  

A

•

•

Select “Add” (  

), choose the environment to place it and give it a name  

Select  

; activate the Bluetooth connection on your tablet/smartphone and approach the  

for 5 s; the ring flashes blue and association is complete.  

• opn = open window (associated with the thermostat via magnetic contact art.  

03980)  

thermostat  

•

Press  

Dial  

B

C

5. For each thermostat, set the functions and parameters.  

6. Go to the “Temperature control” menu and for each thermostat set the time schedules, the  

setpoints for the operating modes and the current time.  

Lightable ring  

• Power on and off.  

CONFIGURATION IN  

Upon power on or off, the thermostat starts in the last operating mode associated  

with it set via the View* App or View Wireless* App.  

1. Wire all the devices in the system (2-way switches, relays, thermostats, gateway, etc.).  

2. Start the View Wireless App and log in with the credentials you just created.  

3. Create the system and the environments.  

• Heating or air conditioning mode selection.  

4. Associate all the devices with the environments, except for the gateway (which should be  

associated last).  

* Only for Bluetooth technology  

To associate the thermostat:  

• Select “Add” (  

• Select  

the thermostat  

• Press  

), choose the environment to place it and give it a name  

; activate the Bluetooth connection on your tablet/smartphone and approach  

Ring signalling  

All flashing blue = thermostat in configuration mode  

for 5 s; the ring flashes blue and association is complete.  

5. For every device, set the function, the parameters and any accessory devices (wired or radio  

control and related function).  

All lit amber* = thermostat in heating mode and relay active  

All lit blue** = thermostat in air conditioning mode and relay active  

• Lit amber * = thermostat in heating mode and relay not active  

6. Transfer the configuration of the devices to the gateway and connect it to the Wi-Fi network.  

7. Transfer the system to the Administrator user (who must have created his/her profile on  

MyVimar).  

• Lit blue ** = thermostat air conditioning mode and relay not active  

1

For full details, see the View Wireless App manual that can be downloaded from the www.  

vimar.com website.  

In standby, the brightness is set during configuration; otherwise, the value is the  

maximum one.  

RESETTING THE THERMOSTAT  

• Flashing red = the thermostat, in automatic mode, has lost the hourly value and  

The reset restores the factory settings. Within the first 5 minutes of powering, press  

for 30  

has therefore switched to manual mode.  

2

s; during these 30 s the ring flashes blue and then emits 2 white flashes to confirm the operation.  

When it receives the hourly value from the gateway again, the thermostat returns  

to automatic mode and the flashing ends.  

THERMOSTAT DATE/TIME SETTING  

In the event of a mains voltage outage, if the thermostat is configured in Stand alone and the  

“ON Mode”-“Automatic” is set, the date and time can be inserted directly on the device without  

using the App.  

* Amber with automatic colour or of the selected colour.  

** Blue with automatic colour or of the selected colour.  

1. Press  

; you have entered the “Time entry” phase; during this phase, keys  

,

and  

are not operational.  

2. Turn the ring and display the number representing the desired day of the week (1=Monday,  

N.B. During the selection phases, the display and part 2 of the ring flash and key  

flashes red.  

2=Tuesday, 3=Wednesday and so on).  

If no selection is made within 2 minutes, the thermostat quits the procedure.  

3. Confirm by pressing  

; now proceed and set the time.  

To change the time without a blackout press  

1 to 7 above.  

for 5 s and perform the procedure from point  

4. Turn the ring and display the number representing the hours (00, 01, 02 and so on all the way  

to 23).  

5. Confirm by pressing  

; now proceed and set the minutes.  

6. Turn the ring and display the number representing the minutes (00, 01, 02 and so on all the  

way to 59).  

7. Confirm by pressing  

; the thermostat returns to the state it was in before the blackout and  

the display and part 2 of the ring stop flashing.  

Viale Vicenza 14  

36063 Marostica VI - Italy  

www.vimar.com  

30810.x-02973 02 2302  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	VIMAR 30810.G View Wireless Connected Dial Thermostat Instruction Manual
Make	VIMAR
Language	English
Filetype	PDF (Download)
File size	0.15 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• VIMAR

VIMAR 30810.G View Wireless Connected Dial Thermostat Instruction Manual Overview

Summary of Contents

• Page 1: SMART HOME VIEW WIRELESS Connected dial thermostat Two operating modes (alternative) Stand alone Download the View Wireless App from the stores onto the tablet/smartphone you will be using for configuration. When the device is powered for the first configuration, we recommend you search for any new firmware and perform the update. Select “Add,” choose the environment to place it and give it a name. For each thermostat, set the functions and parameters. The reset restores the factory settings. In the event of a mains voltage outage, if the thermostat is configured in Stand alone and the “ON Mode”-“Automatic” is set, the date and time can be inserted directly on the device without using the App.
• Page 2: Hysteresis for On/Off control is adjustable between 0.1°C and 1°C, with a default of 0.2°C. Proportional band for PID control ranges from 0.5°C to 5°C, defaulting at 3°C. Integrative time for PID control can be set between 5 minutes and 120 minutes, with a default of 20 minutes. Installation and configuration must be performed by qualified personnel in compliance with local regulations. The View Wireless App can be used to associate a contact to turn off the temperature control system in case of an open window. Reaction time can be set between 0 minutes and 30 minutes, with a default of 0 minutes. The device must be installed at a height of 1.5 meters above floor level, avoiding areas affected by heat sources. The front buttons, display, and dial allow for setting and displaying all operating modes of the thermostat. Operating modes include Automatic, Manual, Reduction, Absence, Protection, Off, and Timed Manual. The product must be disposed of properly at the end of its life cycle, following local waste collection regulations.
• Page 3: Connections: Circulation pumps, burners, solenoid valves and temperature probe. Specifications include voltage range of 100-240V~, frequency of 50/60Hz, and current rating of 5(2)A. Model numbers and identifiers are provided, such as 50/6, B.U, and various codes. The document includes a reference to a specific location in Italy.