SALUS Wired Electronic Thermostat – Non-programmable HTR230 User Manual

1

2

Introduction  

Proper thermostat location  

HTR230(20) is a surface-mounted (or on a flush-box) room thermostat  

dedicated for surface heating / cooling control, characterized by high thermal  

inertia. It is connected to the wiring centre, through which you can lower the  

set temperature on it, receiving a signal NSB (night temperature reduction)  

from the weekly thermostat. The room temperature could be set by knob  

use. Thanks to the built-in algorithms, it offers much better temperature  

control accuracy than traditional mechanical thermostats. The thermostat is  

characterized by silent operation.  

Wired electronic thermostat - non-programmable  

Model: HTR230(20)  

Product compliance  

The product complies with the following EU directives: 2014/30/EU,  

2014/35/EU, 2011/65/EU. Full information is available at www.saluslegal.com  

The ideal position to thermostat mounting is about 1,5m under floor level  

far from heating or cooling sources. In addition, the thermostat should not be  

installed behind curtains or other obstacles or in places with high humidity, as  

this will prevent accurate measurements of room temperature. The thermostat  

must not be exposed to sunlight. Do not place the thermostat on an outer wall.  

Note!  

This document is a quick guide to the installation and operation of the product  

and indicates its main features and functions. Detailed information is available  

in the full manual, which is available at www.salus-controls.eu and must be  

used for proper installation and operation of the product.  

Connection description  

Note:The thermostat is compatibile with the following Salus wiring  

centre models: KL06 230V, KL08NSB 230V, KL04NSB 230V or directly to  

the actuator.  

SAFETY INFORMATIONS:  

Use in accordance with national and EU regulations. Use the device as intended  

and keep it dry. Product for indoor use only. Please read the entire manual  

before starting the installation and using the product.  

Ver. 1  

Date of issue: 10 VI 2020  

Power supply: 230V  

User manual  

NSB input  

INSTALLATION:  

T30NC  

Actuator  

HTR 230  

Thermostat  

CO  

L

Installation must be carried out by a qualified person, with appropriate  

electrical authorisations, in accordance with national and EU standards and  

regulations. The manufacturer shall not be liable for failure to comply with the  

manual.  

N

/

SALUS CONTROLS DISTRIBUTOR:  

QL CONTROLS Sp. z o.o., Sp. k.  

ul. Rolna 4,  

43-262 Kobielice,  

Poland  

L

N

NOTE:  

There may be additional protection requirements for the entire installation.  

The installer shall be responsible for compliance with such requirements.  

Importer:  

SALUS Controls Plc  

Units 8-10 Northfield Business Park  

Forge Way, Parkgate  

Rotherham  

S60 1SD  

United Kingdom  

SL  

HTR 230  

Thermostat  

CO  

L

KL08 NSB  

Wiring centre  

L

N

N

Package content  

Symbols explanation:  

Terminal Description  

L, N  

NSB  

SL 230 V AC output signal  

Power supply (230V AC)  

www.salus-controls.eu  

SALUS Controls is a member of the Computime Group.  

Front housing  

of the thermostat  

Back housing  

of the thermostat  

Night temperature reduction (230V output)  

In accordance with the product development policy, SALUS Controls plc reserves  

the right to change specifications, design, and materials used in production,  

presented in this manual, without prior notice.  

Wired electronic thermostat - non-pro-  

grammable  

Model: HTR230(20)  

CO  

Switching jumper between heating and cooling (input 230V AC)  

Note: The following designations are used interchangeably for products:  

= SL  

= NSB  

User manual  

User manual  

Mounting screws  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	SALUS Wired Electronic Thermostat – Non-programmable HTR230 User Manual
Make	SALUS
Language	English
Filetype	PDF (Download)
File size	0.12 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• SALUS

SALUS Wired Electronic Thermostat – Non-programmable HTR230 User Manual Overview

Summary of Contents

• Page 1: Introduction HTR230(20) is a surface-mounted room thermostat dedicated for surface heating/cooling control, characterized by high thermal inertia. The room temperature could be set by knob use, offering better temperature control accuracy than traditional mechanical thermostats. The ideal position for thermostat mounting is about 1.5m under floor level, away from heating or cooling sources. The thermostat must not be exposed to sunlight or installed behind curtains or in high humidity areas. This document is a quick guide to the installation and operation of the product. Installation must be carried out by a qualified person, in accordance with national and EU standards and regulations. The product complies with EU directives: 2014/30/EU, 2014/35/EU, 2011/65/EU. Use the device as intended and keep it dry; it is for indoor use only. There may be additional protection requirements for the entire installation. In accordance with the product development policy, specifications and designs may change without prior notice.
• Page 2: Montage Jumpers for additional settings Cooling blocking function: Set the jumper to ON in cooling mode if 230V AC will appear at the CO terminal. The LED lights up blue when the thermostat sends a signal for cooling. Night setback – NSB function: The NSB function enables automatic reduction of the temperature setpoint on the daily thermostats via the programmable thermostat connected to the wiring centre. The thermostat will automatically reduce the temperature setpoint on the knob by 2° or 4° when the night mode is activated. For the proper NSB function work, an appropriate cable connection is required. The functions of the HTR230(20) thermostat can be switched on and off by jumpers. Valve protection: Set the jumper to ON to enable or OFF to disable the function. The thermostat gives a possibility to choose the mode of controlling the room temperature by PWM algorithm or hysteresis +/-0.5°C. Jumpers 1 to 5 correspond to the number of actuators connected. Heating or cooling mode is based on the voltage sent to the CO terminal.